manualshive.com logo in svg

Sinclair FC-D09AI, Руководство пользователя

Поделиться
Скачать
Sinclair FC-D09AI Скачать руководство пользователя страница 10

The Codes of Failure Definitions are as Follows:

Fault code

Meaning

Compressor high pressure protection unit stop
Indoor unit anti-freezing protection
Low-pressure protection unit stop
Air exhaust protection unit stop
Over current protection unit stop
Communication malfunction unit stop
Unit modes conflict
 Jumper  malfunction
Defrosting /Heating oil return
Compressor overload protection unit stop
System Unit  malfunction
IPM modular protection unit stop
PFC protection unit stop
Compressor malfunction

Indoor pipe temp. sensor malfunction

Outdoor ambient temp. sensor malfunction
Outdoor pipe temp. sensor malfunction
Outdoor air exhaust temp. sensor malfunction

E2 PROM Error
Wire controller ambient temp. sensor malfunction

1
2
3
4
5
6
7
8
9

10
11
12
13
14
15
16
17
18
19
20
21
22

E1
E2
E3
E4
E

5

E6
E

3

E3

defrost

E5
F

2

E

5

E5

E9
E9

F0
F1
F3
F2
F4

E3

F5

Water spill protection

Indoor ambient temp. sensor malfunction

Wire controller

 Failure Display 

When  there  is  failure  in  the  unit  operation,  “ERROR”  will 
flash on the LCD of the wire controller and the code of fai-
lure will also be displayed. When there are multiple failures 
at  the  same  time,  the  codes  of  failures  will  be  displayed 
one  after  one  on  the  wire  controller.  The  first  digit  of  the 
code denotes the system number. When there is only one 
system,  the  system  number  is  not  displayed.  The  last  two 
digits  denote  the  detailed  failure  code.  For  example,  the 
code  in  Figure  13  means  low  pressure  protection  of  com-
pressor.

• The “EH” failure is displayed, cut off the power supply of the unit immediately,   
   and only ask professional serviceman to repair the unit!

E5  Material Malfunction Will Be Showed By  The Indicator Light  On The Mother Board Of Outside Unit

9

Содержание FC-D09AI



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды