background image

Preface

As Navico is continuously improving this product, we retain the right to make changes to the
product at any time which may not be reflected in this version of the manual. Please contact
your nearest distributor if you require any further assistance.
It is the owner’s sole responsibility to install and use the instrument and transducers in a 
manner that will not cause accidents, personal injury or property damage. The user of this 
product is solely responsible for observing safe boating practices.
NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL
LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE
OR THAT MAY VIOLATE THE LAW.
Governing Language: This statement, any instruction manuals, user guides and other 
information relating to the product (Documentation) may be translated to, or has been 
translated from, another language (Translation). In the event of any conflict between any
Translation of the Documentation, the English language version of the Documentation will be 
the official version of the Documentation.
This manual represents the product as at the time of printing. Navico Holding AS and its 
subsidiaries, branches and affiliates reserve the right to make changes to specifications 
without notice.

Copyright

Copyright © 2014 Navico Holding AS.

Warranty

The warranty card is supplied as a separate document.
In case of any queries, refer to the brand web site of your display or system:
www.simrad-yachting.com

Declarations and conformance

This equipment is intended for use in international waters as well as coastal sea areas 
administered by countries of the E.U. and E.E.A. 

Compliance Statements

The Simrad NSS evo2 series;
• 

complies with CE under R&TTE directive 1999/5/EC

• 

complies with the requirements of level 2 devices of the Radio-communications 
(Electromagnetic Compatibility) standard 2008

The relevant Declaration of Conformity is available on the following website, under the model 
documentation section:
www.simrad-yachting.com

Warning

The user is cautioned that any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the

Содержание NSS evo2

























































Отзывы: