Simrad ITI TRAWL SYSTEM Скачать руководство пользователя страница 31

Страница: 31 / 36

Instruction manual

857-164777 / A

NMEA Input to ITI

$SDDBS,x.x,f,y.y,M,z.z,F*hh<cr><lf> Sounder Depth Below Surface

SD represents Sounder Depth.

DBS represents Depth of water Below Surface.

x.x,f is the depth in feet.

y.y,M is the depth in metres.

z.z,F is the depth in fathoms.

Note

Only one of the depth values is required.

$--DBT,,,y.y,M,,*hh<cr><lf> Sounder Depth Below Transducer

-- Means: accept any combination.

DBT represents the Depth of water Below the Transducer.

x.x,M is the depth in metres.

@SSTPP,x,M,y,P,z,M,nn*hh<cr><lf> Position of target or marker

SS represents Receive from Scanning Sonar.

TPP represents Target Position in Polar co-ordinates.

x,M is the horizontal range in metres to the target.

y,P is the bearing to the target relative to the vessel’s heading

- requires gyro input on both Sonar and ITI for reliable data.

z,M is the target’s depth in metres below the surface.

nn is the target identification code: 0 means echo target tracked, 10

means position tracked.

$--GLL,ddmm.hh,N,dddmm.hh,W*hh<cr><lf> Geographical position

-- is the code for the type of system used. -- will be OM if Omega,

LC if Loran-C, GP if GPS, DE if decca etc.

GLL represents Geographical Latitude, Longitude.ddmm.hh,N is the

latitude position in Deg.Min.Hundredths, N=North, S=South.

dddmm.hh,W is the longitude position, Deg.Min.Hundredths, W=West,

E=East.

Note

The ITI system will only use the ZDA sentence for time input.

All manuals and user guides at all-guides.com

all-guides.com

Содержание ITI TRAWL SYSTEM





































Результаты поиска

Содержание ITI TRAWL SYSTEM

Отзывы:

Похожие инструкции для ITI TRAWL SYSTEM

Бренды по названию

Популярные бренды

Simrad ITI TRAWL SYSTEM, Инструкция по эксплуатации

Результаты поиска

Содержание ITI TRAWL SYSTEM

Отзывы:

Похожие инструкции для ITI TRAWL SYSTEM

Бренды по названию

Популярные бренды