manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Navigating

About navigating 

The navigation function included in the system allows you to
navigate to the cursor position, to a waypoint, or along a predefined
route.
If autopilot functionality is included in your system, the autopilot
can be set to automatically navigate the vessel.
For information about positioning waypoints and creating routes,
refer to 

"Waypoints, routes, and tracks"

 on page 53.

Navigation panels

The Nav panel

The Nav panel is activated from the Home page, either as a full page
panel or as part of a split page.

A Data fields
B Vessel heading

C

Bearing to next routepoint

D Route information

Indicates the distance of the route, the route name, and the
estimated time to reach the end of the route.

6 

Navigating

 | GO XSE/XSR Operator Manual

63

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Eclipse Combustion 6500 Instruction Manual preview
6500
Бренд: Eclipse Combustion Страницы: 46
Bard Duet Instructions For Use preview
Duet
Бренд: Bard Страницы: 2
NORLUX Ledpro Helios Installation Manual preview
Ledpro Helios
Бренд: NORLUX Страницы: 2
BACtrack S75 Owner'S Manual preview
S75
Бренд: BACtrack Страницы: 13
TA Instruments DHR Series Getting Started Manual preview
DHR Series
Бренд: TA Instruments Страницы: 35
CAE Healthcare Ares User Manual preview
Ares
Бренд: CAE Healthcare Страницы: 108
Cannon CT-1000 Manual preview
CT-1000
Бренд: Cannon Страницы: 36
EASTERN INSTRUMENTS CentriFlow Manual preview
CentriFlow
Бренд: EASTERN INSTRUMENTS Страницы: 93
EarthQuake 9800B Operating & Parts Manual preview
9800B
Бренд: EarthQuake Страницы: 12
Pari Vortex Instructions For Use preview
Vortex
Бренд: Pari Страницы: 2
IDS Dual Product Manual preview
Dual
Бренд: IDS Страницы: 2
Uchida Yoko BC-10 Service Manual preview
BC-10
Бренд: Uchida Yoko Страницы: 40
TAKAYA APT-9411 Series Service Manual preview
APT-9411 Series
Бренд: TAKAYA Страницы: 77
Tadano TR-800XXL4 Service Manual preview
TR-800XXL4
Бренд: Tadano Страницы: 402
Vaillant VPS R 100/1 M Installation And Maintenance Instructions Manual preview
VPS R 100/1 M
Бренд: Vaillant Страницы: 76
H2flow levelsmart Quick Start Manual preview
levelsmart
Бренд: H2flow Страницы: 2
V-TAC VT-524-S Installation Instruction preview
VT-524-S
Бренд: V-TAC Страницы: 27
Yacht Sentinel YS PRO Manual preview
YS PRO
Бренд: Yacht Sentinel Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды