manualshive.com logo in svg

Simrad GO XSE Series, Руководство оператора


Поделиться
Скачать
background image

Selecting the radar source

You specify the radar in the radar panel by selecting one of the
available radars in the radar source menu option. If you have a
multiple radar panel page, the radar is set individually for each radar
panel. Activate one of the radar panels, and then select one of the
available radars in the radar source menu option. Repeat the
process for the second radar panel, and select an alternative radar
for this panel.

Ú

Note: 

The 3-digit radar source number is the last 3 digits of the

radar's serial number.

Radar operational modes

The radar’s operational modes are controlled from the Radar panel
menu. The modes available are dependent on your radar's
capability.

Standby

The power to the radar scanner is on, but the radar is not
transmitting.

Ú

Note: 

You can also put the radar in standby mode from the

System Controls dialog.

Power off

The power to the radar scanner is turned off. The power off option is
only available when the radar is in standby mode.

Note: 

Not all radars can be powered off using the Power off menu

option. For alternative power ON/OFF options refer to the radar
installation manual.

Power save

The power save menu option applies the settings made in the
power save settings dialog to the radar source. The power save
menu option is only available when the radar is in standby mode.
Select the standby option, and then the transmit option to return to
normal transmit mode.

Radar

 | GO XSE/XSR Operator Manual

109

Содержание GO XSE Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GO XSE Series

Pall T Series Care And Use preview
T Series
Бренд: Pall Страницы: 51
ZAMST A1 Instructions For Use Manual preview
A1
Бренд: ZAMST Страницы: 21
ZOLL R Series In-Service Manual preview
R Series
Бренд: ZOLL Страницы: 5
Accu-Chek Compact Pocket User Manual preview
Compact
Бренд: Accu-Chek Страницы: 3
iBin Compact Installation Instructions preview
Compact
Бренд: iBin Страницы: 2
Kapriol 27977 Manufacturer'S Instruction And Information preview
27977
Бренд: Kapriol Страницы: 32
JABO 4236 Installation Manual preview
4236
Бренд: JABO Страницы: 4
Gardena 1407 Operator'S Manual preview
1407
Бренд: Gardena Страницы: 13
Obdstar BT06 Instructions For Functions preview
BT06
Бренд: Obdstar Страницы: 10
Panasonic SF2B Series Instruction Manual preview
SF2B Series
Бренд: Panasonic Страницы: 30
HABYS Agila 2 Instruction Manual preview
Agila 2
Бренд: HABYS Страницы: 16
R-Biopharm RIDA qLine ZG2601 Operation Instructions Manual preview
RIDA qLine ZG2601
Бренд: R-Biopharm Страницы: 23
Samson 1352 Parts And Technical Service Manual preview
1352
Бренд: Samson Страницы: 2
uniprox JT40 Instruction Manual preview
JT40
Бренд: uniprox Страницы: 3
Össur QUICK-ALIGN Vari-Flex Instructions For Use Manual preview
QUICK-ALIGN Vari-Flex
Бренд: Össur Страницы: 36
Össur Patriot Collar Instructions For Use preview
Patriot Collar
Бренд: Össur Страницы: 2
Össur Unloader One Instructions For Use Manual preview
Unloader One
Бренд: Össur Страницы: 8
Walimex Pro LED Round 200 Instruction Manual preview
LED Round 200
Бренд: Walimex Pro Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды