Simpson 260 series 5M Скачать руководство пользователя страница 9

10

*Accuracies specified are for the 260 in a horizontal position.
**Responds to the average value of an AC current, and is calibrated to indicate
the RMS value of a pure sine wave.
***Per ANSI C39.5 April 1974: “The specified voltage with respect to ground,
which may be safely and continuously applied to the circuit of an Instrument.”

1.10 Definition of Accuracy

The voltage and current accuracy of this Instrument is commonly expressed as a
percent of full scale. This should not be confused with accuracy of reading (indi-
cation). For example, +2% of full scale on the 10 volt range allows an error of
±0.20V at any point on the dial. This means that at full scale, the accuracy reading
would be ±2%, but at half scale it would be ±4%. Therefore, it is advantageous to
select a range which gives an indication as near as possible to full scale.

1.11 Safety Considerations

This Operator’s Manual contains special caution and warning symbols which
alert the user to hazardous operating and service conditions. These symbols
appear throughout this publication where applicable, and are defined on the
inside front cover of this manual under NOTES AND SAFETY INFORMATION.
Please adhere to these instructions to ensure the safety of operating and servic-
ing personnel and to retain the operating conditions of the Instrument.

1.12 Audio Alarm

The 260-8P Audio Alarm is a transducer which will emit an audible sound when
the operator of the Instrument intends to quickly determine the continuity of a
circuit.

NOTE:

 Not protected by Electronic Overload Protection System.

Do not make Circuit Continuity Tests with electrical power “ON”. Turn “OFF” all
electrical power.

Table 1-2.  Items and Accessories Furnished with This Instrument

Quantity

Description

Number

 1

Test Lead Set - one red and one black (48” long)

00043

each with combination probe tip and removable
rubber-sleeved alligator clip.

*1

1.5 Volt, D Cell, NEDA 13F

*1

9.0 volt Cell, NEDA 1604A

 2

1Amp, 250V Fuse, Littlefuse Type #312001

 1

2A, 600V Fuse, Littlefuse Type BLS or
(Bussman Type BBS)

 1

Operator’

9

3

3

4

1

1

-

6

l

a

u

n

a

M

 

s

*Batteries are standard items replaceable from local retail stores.

!

www.calcert.com

[email protected]

1.888.610.7664

0

5

10

15

20

25

30

Содержание 260 series 5M




























Отзывы: