SimpliFire SF-ALL48-BK Скачать руководство пользователя страница 11

Страница: 11 / 11

SimpliFire • SF-ALL48-BK, SF-ALL60-BK Service Manual Rev. B • 2040-960 • 3/18

SimpliFire, a brand of Hearth & Home Technologies

7571 215

Street West, Lakeville, MN 55044

www.hearthnhome.com

Please contact the SimpliFire customer/technical

support hotline at 877-320-0730 with any questions

or concerns.

WARNING! Risk of Damage or Personal Injury!

not use supplied masonry anchors on hollow walls,

sheathed with wood, gypsum wallbaord, drywall or other

materials.

Figure 31. Bracket Attachment

Mounting Hooks

Point Up

Note:

For non-masonry walls,

at least

two

mounting points

(screws ST5X40) must align

with structural framing member.

WARNING! Risk of Fire, Electrical Shock and Injury!

Ensure the power cord is not installed so that it is pinched

or against a sharp edge and ensure that the power cord is

stored or secure to avoid tripping and snagging.

Power Cord Kit Installation

The appliance power cord has a three pin NEMA-5-15P

plug. The power cord should not be used unless a

grounded receptacle is available.
1. Remove the terminal block cover plate located on

the right end of the appliance.
2. Disconnect the terminal block from the three wires

inside the appliance. Discard the terminal block

cover plate.
3. Connect the three appliance wires to the terminal

block supplied with the power cord kit. See Figure

32.
4. Replace cord kit terminal block cover plate and

retaining screws. Plug cord into nearest outlet.

Figure 32. Optional Power Cord Assembly Installation

RED

BLUE

Wire Diagram

YELLOW / GREEN

Содержание SF-ALL48-BK












Результаты поиска

Содержание SF-ALL48-BK

Отзывы:

Похожие инструкции для SF-ALL48-BK

Бренды по названию

Популярные бренды

SimpliFire SF-ALL48-BK, Руководство по обслуживанию

Результаты поиска

Содержание SF-ALL48-BK

Отзывы:

Похожие инструкции для SF-ALL48-BK

Бренды по названию

Популярные бренды