background image

ENGINE

11 HP I/C — Briggs & Stratton

Horsepower

10.5 HP @ 3600 rpm

Cylinders

1

Bore

3.44 In. (87 mm)

Stroke

3.06 In. (77 mm)

Displacement

28.4 Cu. In. (465 cc)

Construction

Cast Iron Sleeves, Aluminum Crankcase

Electrical 

12 Volt, 3 Amp D.C. Unregulated Battery:

System

200 Cold Cranking Amps, 23 min. Reserve
Capacity

Ignition

Electronic, Solid State, Maintenance Free

Air Cleaner

Reusable Oil Foam Element

Lubrication

Splash Lube

Oil Capacity

3 Pints (1.42 L)

Fuel Capacity

2 Gal. (7.57 L)

Muffler

Quiet Compact, Low Back Pressure

13 HP Diamond OHV — Briggs & Stratton

Horsepower

13 HP @ 3600 rpm

Cylinders

1

Bore

3.44 In. (87 mm)

Stroke

3.06 In. (77 mm)

Displacement

28.4 Cu. In. (465 cc)

Construction

Cast Iron Sleeves, Aluminum Crankcase

Electrical 

12 Volt, 3 Amp D.C. Unregulated Battery:

System

200 Cold Cranking Amps, 23 min. Reserve
Capacity

Ignition

Electronic, Solid State, Maintenance Free

Air Cleaner

Pre-Cleaned Air to Paper Filter

Lubrication

Splash Lube

Oil Capacity

2 Pints (1.42 L)

Fuel Capacity

2 Gal. (7.57 L)

Muffler

Quiet Compact, Low Back Pressure

14 HP Command™ — Kohler

Horsepower

14 HP @ 3600 rpm

Cylinders

1

Bore

3.43 In. (87 mm)

Stroke

2.64 In. (67 mm)

Displacement

24.3 Cu. In. (398 cc)

Construction

Overhead Valve, Cast Iron Sleeves, 
Aluminum Crankcase

Electrical 

12 Volt, 15 Amp Alternator Regulated Battery:

System

200 Cold Cranking Amps

Ignition

High Energy Electronic Ignition

Air Cleaner

Ducted Paper Cartridge and Foam Pre-cleaner

Lubrication

Full Pressure Lube with Oil Filter

Oil Capacity

4 Pints (1.9 L)

Fuel Capacity

2 Gal. (7.57 L)

Muffler

Quiet Compact, Low Back Pressure

TRANSMISSION

Gear Models

Type

Spur Gear

Material

Gear: Powered Metal
Shaft: Hardened
Bearings: Needle Roller and Bushings

Lubrication

Bentonite Grease. Transmission is a sealed unit.

Differential

Bevel Gear Type

Gear Range

Five Forward, One Reverse

Ground Speeds

lst: 

1.2 MPH (1.9 km/h)

2nd: 

2.4 MPH (3.9 km/h)

3rd: 

3.5 MPH (5.6 km/h)

4th: 

4.4 MPH (7.1 km/h)

5th: 

5.6 MPH (9.0 km/h)

Reverse: 

2..0 MPH (3.2 km/h)

Hydro Models

Type

Hydrostatic

Lubrication

Transmission is a Sealed Unit

Differential

Bevel Gear Type

Ground Speeds

Infinite Forward: 0-5.2 MPH (0-8.4 km/h)
Reverse: 0-2.3 MPH (0-3.7 km/h)

CONTROLS

Steering

Full Circle Steering Wheel
System Gear and Sector

Clutch/Brake 

Location Right Front

Pedal

Combination Clutch/Brake Pedal

Parking Brake

Dash Lock Finger Release

Ground Speed

Dash Mounted

Shift Lever
Throttle Control

Combination Speed & Choke Control on right side 
of seat deck

Key Switch

Starter and Magneto ON/OFF Switch located on 
left side of seat deck

Mower Drive

Electric Clutch PTO Switch located on right side of
seat deck

Mower Cutting

Infinite Height Control on Steering Column

Height

CHASSIS

Frame

Heavy Gauge , Deep Drawn Steel

Front Axle

Self-Leveling Quick Hitch

Seat Deck

Lightweight Polymer Alloy

Seat

Molded Type with Foam Cushion and Spring 
Construction

Front Wheels

Tire Size 13 x 5.00-6 
Pneumatic Inflation Pressure 10 -12 psi 
(68 - 82 kPa)

Rear Wheels

Tire Size 16 x 6.50-8
Pneumatic Inflation Pressure 10 -12 psi             
(82 - 103 kPa)

Accessibility

Seat Deck Tips Forward

Seat

Type Bucket, High Back, Adjustable w/
Spring Suspension, Fore and Aft Adjustable

Fuel Tank

Material: Non-Corrosive Polyethylene Alloy 
Capacity: 2 Gallons (7.5 L)

Turning Radius

Inside Rear Tire 12 In. (30.2 cm)

NOTE: Specifications are correct at time of printing and are subject to change without  notice.

30

Specifications

Содержание Coronet 1693030







































Отзывы: