Simplicity 1692917 Скачать руководство пользователя

Страница: 19 / 20

Troubleshooting & Service

REPLACING THE DRIVE BELT

1. Remove Engine Key from switch.

2. Remove belt and engine covers.

3. Move the Auger Control on the handle and slip the

belt out from between the brake lever and roller and
away from the idler pulley.

4. Remove the belt from the engine and auger pulleys.

5. Install new belt around engine and auger pulleys and

under idler pulley.

The ribbed side of the belt must be

to the inside, against auger and engine pulleys.

6. Slip the new belt into place between brake lever and

roller.

7. Start the engine and engage/disengage the auger

control several times. Make certain that auger stops
turning within 5 seconds after the control is released.

8. If the auger does not stop turning within 5 second

after the control is released, adjust the tension on the
control cable by following the Adjusting Control Cable
procedure in the adjustments section of this manual.

9. Reinstall the belt and engine covers.

Figure 14. Drive Belt Replacement

REPLACING THE SCRAPER BLADE

1. Remove Engine Key from switch.

2. Remove the two bolts and nuts securing the Scraper

Blade to the auger housing. (Retain the bolts and
nuts for attaching the new blade.)

3. Remove the worn Scraper Blade.

4. Install the new Scraper Blade and secure it with the

three bolts and nuts saved in step 2 above.

Figure 15. Removing Scraper Blade

SERVICING THE SPARK PLUG

1. Remove Engine Key from switch.

2. Remove the engine cover. (See page 13.)

3. Disconnect the wire from the spark plug.

4. Inspect the Spark Plug and clean. If necessary,

replace the it with a new Spark Plug as recommend-
ed in the Engine Owners Manual.

5. Adjust the gap on the Spark Plug to .030 inches

(.762 mm) using a gauge.

6. Reinstall the plug and tighten firmly.

7. Reconnect Spark Plug wire.

8. Reinstall engine cover.

Figure 16. Servicing Spark Plug

Spark Plug
Wire

Scraper Blade, Bolts & Nuts

Engine

Pulley

Idler

Pulley

Brake

Lever/Roller

Drive Belt

Auger Pulley

Содержание 1692917





















Результаты поиска

Содержание 1692917

Отзывы:

Похожие инструкции для 1692917

Бренды по названию

Популярные бренды

Simplicity 1692917, Как пользоваться инструкцией

Результаты поиска

Содержание 1692917

Отзывы:

Похожие инструкции для 1692917

Бренды по названию

Популярные бренды