background image

How to use this file...(Operators Manuals)

————————————————————————————————————————————–––

Instructions for

Print Vendors (Paper Manuals)

Paper Size:

* 11 x 17
* Body—50 lbs brilliant white offset or equivalent.
* Cover—on pre-printed two-tone “Swash” stock.

P r e s s :

* Body—1-color, 2-sided
* Cover imprint —1-color, 1-sided

Bindery:

* Saddle Stitch, Face Trim
* Face Trim

C O V E R S :

*  This file may contain several manuals, which differ only in their covers.
* Covers are all present at the beginning of this file.
* Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover.
• Check the front cover for the individual part number (typically a 171xxxx number).

B O D Y :

•  The body of the manual is identical, regardless of the cover used.
* REMEMBER: ODD number pages are ALWAYS right hand pages, and EVEN number are ALWAYS 

left hand pages.

G e n e r a l :

*  This instruction page is NOT part of the manual and must NOT be printed.
• Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY, 

and should NOT be printed.

————————————————————————————————————————————–––

Содержание 1692917





















Отзывы: