background image

Table Of Contents

 RULES

General ...........................................................

2

Preparation.. ..................................................
Operation.. .....................................................

Maintenance

Storage.. ..............................

Safety Decals ................................................

CONTROLS

Snowthrower Controls .................................

Engine Controls.. ...........................................

4

Engine Speed.. ..............................................
Ground Speed Selector.. ..............................
Deflector.. ......................................................

Scraper Bar

Skid Shoes ...........................

OPERATION

General ..........................................................

Operation on Slopes ....................................
Checks Before Each Start-Up.. ....................

Starting The Engine.. ....................................

Operating The Snowthrower .......................

After Each Use ..............................................

REGULAR MAINTENANCE

Normal Care Chart .........................................

8

Off-Season Storage .......................................

8

Starting After Storage ..................................
Checking Auger Gear Case.. .......................
Lubrication ....................................................
Checking T i r e Pressure ...............................

SERVICE

Troubleshooting .........................................

Shift Control Adjustment ........................... . l l
Drive Belts ...................................................

. l l

Roller Chain Replacement.. .......................

Shear Pin Replacement.. ............................

Wheel Axle Bearing Replacement.. ............ 14

Auger Shaft Bearing Replacement ...........

SPECIFICATIONS.. ............................................

COMMON REPLACEMENT PARTS .................
ACCESSORIES .................................................
TECHNICAL MANUAL AVAILABILITY.. ...........

This manual covers the following models:

Model

Mfg. No.

1691411

I

1 6 9 1 4 1 3
1 6 9 1 4 1 4

I

1 6 9 2 6 1 5

Record your model number, manufacturer number and
serial number in the space provided for easy reference.

The 

 I.D. tag is located on the rear of the

frame.

Refer to the Engine Owner’s Manual for location of

engine serial number.

MODEL REFERENCE

Model Number:

Manufacturer Number:

Engine I.D. Number:

Dealer Name/Date Purchased:

A

WARNING

You must read, understand and comply with all safety and operating instructions in this manual before
attempting to set-up and operate your snowthrower.

Failure to comply with all safety and operating instructions can result in loss of machine control, serious
personal injury to you and /or bystanders, and risk equipment and property damage. The triangle in the

text signifies important cautions or warnings which must be followed.

A

WARNING

Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth

defects, or other reproductive harm.

1

I

Содержание 1691411





















Отзывы: