Simplicity 1334 Скачать руководство пользователя | Manualshive

Страница: 14 / 34

background image

10

PUSHING THE MOWER BY HAND

• Disengage the PTO, turn the ignition OFF, and

remove the key.

• Slide the hydraulic release rod forward and lock into

the top of the “T” slot. See Figure 5.

• Grasp the operator presence / parking brake handles

and the handle bar grips at the same time to disen-
gage the parking brake.

The mower can now be pushed by hand.

• After moving the mower, re-engage the transmission

(DRIVE position) by releasing the rod from the “T”
and sliding the release handle towards the rear of the
machine.

Operating the Walk Behind Mower

DO NOT TOW MOWER

Towing the unit will cause hydraulic trans-
mission damage. Do not use another vehi-
cle to push or pull this unit.

Figure 5.

Hydraulic Release Rod

NEUTRAL POSITION

DRIVE POSITION

MOWING

• Make sure the PTO switch is disengaged.

• Start the engine (see STARTING THE ENGINE).

• Set the throttle control to FULL.

• Grasp the operator presence / parking brake handles

and the handle bar grips at the same time to deacti-
vate engine kill system and disengage the parking
brake.

• Engage the PTO by pulling up on the PTO switch.

• Begin mowing. See Lawn Care Section in the back

of this manual for tips on mowing patterns, lawn care,
and trouble shooting information.

• When finished, disengage the PTO.

• Stop the engine (see STOPPING THE MOWER).

MULCH PLATE TAB
LOCATED IN BAFFLE SLOT

STONE GUARD

J-BOLT

SLOT

Figure 4.

Mulch Plate Removal & Replacement

MULCH PLATE REMOVAL &
REPLACEMENT

1. To remove the mulch plate, simply loosen the wing

nut and turn the j-bolt to release it from the stone
guard and remove the plate from the discharge open-
ing.

2. To install the mulch plate, hold the discharge deflec-

tor up and install the mulch plate in the discharge
opening. Make sure the tab of the mulch plate is
resting in the slot in the baffle (see Figure 4).

3. Turn the j-bolt to hook it over the stone guard and

tighten the wing nut to secure the plate.

4. Refer to the Lawn Care & Mowing Information

Section located in the back of this manual for proper
mulching procedures.

«
...
12
13
14
15
16
...
»

Содержание 1334



































Отзывы:

Нет отзывов

Похожие инструкции для 1334

Бренд: Snapper Страницы: 1

Бренд: Snapper Страницы: 40

Greens King V Plus

Бренд: Jacobsen Страницы: 224

30710 Groundsmaster 300

Бренд: Toro Страницы: 20

Бренд: Simplicity Страницы: 32

Бренд: Ryobi Страницы: 16

Бренд: Weed Eater Страницы: 48

Бренд: Makita Страницы: 24

Бренд: Makita Страницы: 140

Бренд: Walker Страницы: 88

Бренд: OHIOSTEEL Страницы: 14

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 60

Бренд: Craftsman Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды