background image

 

 

Engine Operation 17 

6. E

NGINE

O

PERATION

 

6.1 Adding/Checking Oil 

 

 

1. Remove oil tank dipstick (6) and wipe it with a 
clean cloth. 
2. Replace and retighten the dipstick. 
3. Remove the dipstick again and check the oil level. 
It should be at the top of the full indicator on the 
dipstick. 
4. If low, add oil slowly into the oil tank. Do not overfill. 
After adding oil, wait one minute and then recheck the 
oil level. 
5. Replace and retighten the dipstick. 

Tip: 

When adding oil, use provided oil funnel (R). 

 

6.2 Adding Fuel 

 

1. Stop the engine (

→ Stopping Engine

) and let it cool 

at least two minutes before removing the fuel tank 
cap (17). 
2. Clean the fuel cap area of dirt and debris. Remove 
the fuel tank cap and make sure the fuel filter is in 
place. 
3. Fill the fuel tank (16) with fuel. Never overfill the 
fuel tank. Fill tank to no more than ½

  (13 mm) 

below the bottom of the filler neck to provide space for 
expansion caused by the engine heat.   
4. Replace the fuel tank cap. 

 

 

 

IMPORTANT 

• Keep fuel away from sparks, open flames, pilot 
lights, heat, and other ignition sources. 
• Check fuel hoses, tank, caps, and fittings 
frequently for cracks or leaks. Replace if necessary. 
• If fuel spills, wait until it evaporates before starting 
engine. 
• Fill the fuel tank outdoors or in well-ventilated 
areas. 

 

FUEL TANK CAPACITY: 1.4L

 

 

 

WARNING 

•Make sure there is enough fuel in the fuel tank 
before operating the pressure washer. 
• Use only clean, fresh, unleaded fuel. Use a 
minimum of 87 octane / 87 AKI (91 RON). 
• Do not use old gas, and do not mix oil with 
gasoline. 
• Fuel and its vapors are extremely flammable and 
explosive. Fire or explosion can cause severe burns 
or death. 

 

OIL TANK CAPACITY: 0.6L 

 

 

WARNING 

• Always check the oil level before starting the 
engine, making sure the pressure washer is on a 
level surface. 
• Always use oil type 

SAE 10W-30

, which can be 

found at your local 

Canadian Tire 

store (Product # 

28-9301-6). 

 

 

IMPORTANT 

Oil has been drained for shipping. Failure to fill 
engine with oil before starting engine will result in 
permanent damage and will void engine warranty. 
Add oil according to the instructions. 

10 

Содержание Platinum 039-8569-0



























Отзывы: