Simex SRP-147-XC Скачать руководство пользователя страница 6

Страница: 6 / 52

This equipment is not intended for use in residential environments and may
not provide adequate protection to radio reception in such environments.

DEVICE INSTALLATION

The unit has been designed and manufactured in a way assuring a high level of user

safety and resistance to interference occurring in a typical industrial environment. In order to

take full advantage of these characteristics installation of the unit must be conducted correctly

and according to the local regulations.

- Read the basic safety requirements on page 3 prior to starting the installation.

- Ensure that the power supply network voltage corresponds to the nominal

voltage stated on the unit’s identification label.

- The load must correspond to the requirements listed in the technical data.

- All installation works must be conducted with a disconnected power supply.

- Protecting the power supply connections against unauthorized persons must be

taken into consideration.

4.1.

UNPACKING

After removing the unit from the protective packaging, check for transportation damage. Any

transportation damage must be immediately reported to the carrier. Also, write down the unit

serial number located on the housing and report the damage to the manufacturer.

Attached with the unit please find:

- user’s manual,

- warranty,

- assembly brackets - 2 pieces.

4.2.

ASSEMBLY

- The unit is designed for mounting inside housings (control panel, switchboard)

insuring appropriate protection against surges and interference. Metal housings

must be connected to ground in a way that complies with the governing

regulations.

- Disconnect the power supply prior to starting assembly.

- Check the connections are wired correctly prior to switching the unit on.

In order to install the unit, a 138.5 x 67 mm mounting hole (Figure 4.1) must be

prepared. The thickness of the material of which the panel is made must not exceed

5mm. When preparing the mounting hole take the grooves for catches located on

both sides of the housing into consideration (Figure 4.1). Place the unit in the

mounting hole inserting it from the front side of the panel, and then fix it using the

brackets (Figure 4.2). The minimum distances between the centre points of multiple

units - due to the thermal and mechanical conditions of operation - are 163 mm x

91mm (Figure 4.3).

Содержание SRP-147-XC





















































Результаты поиска

Содержание SRP-147-XC

Отзывы:

Похожие инструкции для SRP-147-XC

Бренды по названию

Популярные бренды

Simex SRP-147-XC, Руководство пользователя

Результаты поиска

Содержание SRP-147-XC

Отзывы:

Похожие инструкции для SRP-147-XC

Бренды по названию

Популярные бренды