Simex SLN-94 Скачать руководство пользователя страница 25

Страница: 25 / 44

User manual - COUNTER SLN-94

7.1.

PROGRAMMING MENU

To enter main menu (being in the measurement mode) operator must to press and hold

at least 2 sec.

[ENTER/MENU]

button.

If the user password is defined (see parameter

“Cod“

), operator have to enter correct one

before proceeding to menu options . Entering of the passwords is being made by changing of
particular digits by

[^]

buttons, and accepting of password by

[ENTER/MENU]

button.

After entering of last digit of the password first menu position will be displayed (if the password
is correct) or warning ”

Err

” in other case.

Pay attention when device parameters are being changed. If it is possible, turn off

controlled installation (machine).

Functions of the buttons while sub-menu and parameters choice:

Buttons signed

[^]

are used to change value of particular digit (digit above

particular button) and change of current menu position. The name of

selected option is displayed on the left (green) display. The right (red)

display shows current menu name or is dimmed.

Operation of

[ENTER/MENU]

button depend on present menu position:

•

if the name of some sub-menu is displayed - enter this sub-menu; name

of the first parameter (or next level sub-menu) is displayed,

•

if the name of some parameter is displayed - enter the edition of this

parameter; present value of the parameter is displayed,

After pressing of

[ENTER/MENU]

button, name of current menu is scrolled

from the left to the right display, and on the left display name of submenu or

current value of selected parameter is displayed.

[ESC/RESET]

button allow user to exit present menu level and goes to

upper level menu (or measurement mode).

After about 1 min. since last use of the buttons, device exits the menu mode and

returns to the measurement mode (only if no parameters are in editing mode).

7.2.

PARAMETERS EDITION

To start edition of any parameter user should select name of desired one using

[^]

buttons and then

[ENTER/MENU].

Presently edited numerical value, or list-type value flashes on the left (green) display. The right

(red) display shows the name of edited parameter at the same time.

MENU

ENTER

ESC

RESET

Содержание SLN-94













































Результаты поиска

Содержание SLN-94

Отзывы:

Бренды по названию

Популярные бренды

Simex SLN-94, Руководство пользователя

Результаты поиска

Содержание SLN-94

Отзывы:

Бренды по названию

Популярные бренды