Simex SIN-8 Скачать руководство пользователя страница 6

Страница: 6 / 12

User manual - MODULE SIN-8

Figure 4.2. Terminals description

•

When use of SMPS it is strongly recommended to connect PE wire.

•

All connections must be made while power supply is disconnected !

4.3.

MAINTENANCE

The unit does not have any internal replaceable or adjustable components available to

the user. Pay attention to the ambient temperature in the room where the unit is operating.

Excessively high temperatures cause faster ageing of the internal components and shorten the

fault-free time of unit operation.

In cases where the unit gets dirty do not clean with solvents. For cleaning use warm water with

small amount of detergent or in the case of more significant contamination ethyl or isopropyl

alcohol.

Using any other agents can cause permanent damage to the housing.

Product marked with this symbol should not be placed in municipal waste. Please

check local regulations for disposal and electronic products.

IN8

IN6

GND

IN4

IN7

IN2

IN5

IN3

IN1

voltage
inputs
(0-24V)

IN1÷IN8
inputs ground

bottom view

RS-485

SLAVE

n.c.

IN2

RUN

Tx/

ERROR

IN3

IN4

IN7

IN1

IN5

IN8

IN6

5 6 7 8

+Uz A+ B- -Uz

power supply
ground

power supply

+24V DC

front view

force address

0xFF swich

is available

through this hole

Содержание SIN-8













Результаты поиска

Содержание SIN-8

Отзывы:

Похожие инструкции для SIN-8

Бренды по названию

Популярные бренды

Simex SIN-8, Руководство пользователя

Результаты поиска

Содержание SIN-8

Отзывы:

Похожие инструкции для SIN-8

Бренды по названию

Популярные бренды