Sime MURELLE REVOLUTION 30 Скачать руководство пользователя страница 36

Страница: 36 / 100

5 INSTALLATION

CAUTION

The appliance must only be installed by the

Sime Ltd

Technical Service or by qualified professionals

who

MUST wear

suitable protective safety equipment.

5.1

Receiving the product

Murelle Revolution 30

is delivered in a single unit protected by

cardboard packaging.

Fig. 48

The plastic bag found inside the packaging contains the follow-

ing:

– Installation, use and maintenance manual

– Certificate of warranty

– Hydrostatic test certificate

– Hanging Bracket

– External sensor

– Main control panel (remote)

– Connection pack

– Boiler and heat pump energy labels

– Anti-vibration and spacer panels

– Paper template for boiler installation.

DO NOT

Do not leave packaging material around or near chil-

dren since it could be dangerous. Dispose of it as pre-

scribed by legislation in force.

5.2

Dimensions and weight

Description

Murelle Revolution 30

W (mm)

600

D (mm)

391

H (mm)

900

H1 (mm)

82,5

H2 (mm)

Weight (kg)

103

Fig. 49

5.3

Handling

During transportation, the boiler must be kept in a vertical po-

sition, and knocks against walls or hard surfaces should be

avoided.

DO NOT

Position the appliance horizontally or on its side.

YES

Fig. 50

Содержание MURELLE REVOLUTION 30





































































































Результаты поиска

Содержание MURELLE REVOLUTION 30

Отзывы:

Похожие инструкции для MURELLE REVOLUTION 30

Бренды по названию

Популярные бренды

Sime MURELLE REVOLUTION 30, Инструкция для пользователя, по установке и обслуживанию

Результаты поиска

Содержание MURELLE REVOLUTION 30

Отзывы:

Похожие инструкции для MURELLE REVOLUTION 30

Бренды по названию

Популярные бренды