SimCom SIM800H Скачать руководство пользователя страница 53

Страница: 53 / 70

Smart Machine Smart Decision

Figure 47: GSM antenna matching circuit

R101

，

C101

，

C102 are the matching circuit, the value should be defined by the antenna design. Normally R101 is

Ω

, C101 and C102 are not mounted. The RF connector is used for conduction test. If the space between RF pin

and antenna is not enough, the matching circuit should be designed as in the following figure:

Figure 48: GSM simple antenna matching circuit

Normally R101 is 0

Ω

, C101 and C102 are not mounted.

4.19.2.

Bluetooth antenna interface

The module provides a Bluetooth antenna pad named BT_ANT.

The external antenna must be matched properly to achieve best performance, so the matching circuit is necessary,
the connection is recommended as in the following figure:

GND

Module

BT_ANT

GND

R201

C201

C202

Antenna

SIM800H_Hardware_Design_V1.01

2013-08-20

Содержание SIM800H







































































Результаты поиска

Содержание SIM800H

Отзывы:

Похожие инструкции для SIM800H

Бренды по названию

Популярные бренды

SimCom SIM800H, Руководство по конструкции аппаратуры

Результаты поиска

Содержание SIM800H

Отзывы:

Похожие инструкции для SIM800H

Бренды по названию

Популярные бренды