manualshive.com logo in svg

SilverNet SIL ECHO BS, Руководство пользователя, Страница: 13 / 47

Поделиться
Скачать
SilverNet SIL ECHO BS Скачать руководство пользователя страница 13

 

ECHO MANUAL v1.111

                                       

Page 13 of 47

 

 

2.1.1

   

Status

-

WIRELESS  

The Radio status window displays a summary of the link status information  

▪

 

Wireless mode

: 

The mode the unit is currently set to, there are 4 modes the unit can run in. 

AP Mode

,

 Station Mode

,

 AP WDS Mode and Station WDS Mode

.

 

▪

 

Radio  mode: 

The  working  mode  of  the  radio,  which  supports  802.11a/an  which  are  two 

separate wireless transmission standards. 

▪

 

Channel/Frequency:

 

The radio’s current working channel and working frequency. 

▪

 

Channel  Width:

   

Displays  the  spectral  width  of  the  radio  channel.  A  40  MHz  channel  in  a 

minimal interference environment will give up to twice the bandwidth of a 20 MHz channel. 

▪

 

Country  Code:

 

set the country to which the unit is operating this will affect the channels you 

can use and the power of the radio in order to comply with the countries regulations. 

▪

 

Tx Power:

 The transmission power of the radio. The higher your transmission power the more 

signal strength you will receive on a link.  

▪

 

Max Rate:

 The max transmission rate of the radio. Different channel bandwidth

’s have different 

max rates. A 40 MHz channel max rate is 300Mbps. The higher this rate on both ends of the 

link the better the transmission of the link. 

▪

 

TDMA:

 The status of TDMA - 

‘enabled’ or ‘disabled’. 

 

Station

 status box shows the unit working in Station Mode. 

 

Figure 2-3 Wireless Station Status 

 

▪

 

Up/Down:

 

UP means the Station has successfully connected with the AP. Down means there 

is no link. 

▪

 

SSID:

 

This is the name of the wireless network the AP is transmitting 

Содержание SIL ECHO BS
















































Отзывы:

Нет отзывов