background image

www.silverlinetools.com

7

180W Detail Sander 90mm

261345

Accessories

•  A full range of sanding sheets and accessories is available from your 

Silverline stockist

Maintenance

General inspection 

•  Regularly check that all the fixing screws are tight. They may vibrate 

loose over time

•  Inspect the supply cord of the tool, prior to each use, for damage or wear. 

Repairs should be carried out by an authorised Silverline  service centre. 
This advice also applies to extension cords used with this tool

Cleaning

WARNING:

 ALWAYS wear protective equipment including eye protection and 

gloves when cleaning this tool.
•  Keep your tool clean at all times. Dirt and dust will cause internal parts to 

wear quickly, and shorten the device’s service life

•  Clean the body of your machine with a soft brush, or dry cloth
•  Never use caustic agents to clean plastic parts. If dry cleaning is not 

sufficient, a mild detergent on a damp cloth is recommended

•  Water must never come into contact with the tool
•  Ensure the tool is thoroughly dry before using it
•  If available, use clean, dry, compressed air to blow through the ventilation 

holes (where applicable)

Storage

•  Store this tool carefully in a secure, dry place out of the reach of children

Hook and loop surfaces   

 

•  Hook and loop surfaces need to be clean, free of dirt and foreign matter, 

such as hair, fibres, sand etc. 

•  In order to provide adequate adhesion for securing accessories, hook and 

loop surfaces must be in good condition

•  When used extensively, hooks and loops will become elongated or 

broken, and the mechanism cannot provide the required strength of 
adhesion anymore

Note:

 This sander’s hook and loop sanding base is NOT a warranty item. 

Replacement plates can be fitted at an authorised Silverline service centre.

Disposal

Always adhere to national regulations when disposing of power tools that 
are no longer functional and are not viable for repair.
•  Do not dispose of power tools, or other waste electrical and electronic 

equipment (WEEE), with household waste

•  Contact your local waste disposal authority for information on the correct  

way to dispose of power tools

PDF Compressor Pro

Содержание DIY 180W









































Отзывы: