![background image](http://html.mh-extra.com/html/silverline/254155/254155_manual_1273644009.webp)
Scaffold Hook
9
silverlinetools.com
Inspection procedure
• The following procedure helps detect defects potentially resulting in degradation and/or
weakening of scaffold hooks:
1. Inspect for missing or altered parts. Refer to the image in ‘Product Familiarisation’ for
identification. Verify each item is present and has not been tampered with
2. Inspect the entire scaffold hook for cracks, nicks or breaks in the metal. Inspect every
millimetre
Note:
If necessary, clean before inspection, to be able to detect even small hairline cracks.
3. Inspect for deformation, bent or dented parts. Open the Gate and inspect the Nose (1)
of the scaffold hook for signs of wear, distortion or damage
4. Inspect the metal surface for any signs of corrosion. Steel scaffold hooks may show
red dust as evidence of corrosion, aluminium scaffold hooks may develop pitting or
scales
5. Inspect for heat damage, which can usually be seen as discoloration or darkening of
the metal surfaces
6. Perform a functional test: The locking mechanism must move easily, and the scaffold
hook must fully open and close smoothly and easily. When locked, the Gate MUST
NOT open under pressure from any direction
• Inspect all other components or subsystem of the fall arrest equipment according to
manufacturer's instructions
• Record inspection date and results in a dedicated service record (see end of this manual)
Note:
Refer to ‘Service life and product obsolescence’ if any damage or other defects are detected
during inspection.
Cleaning
Note:
Correct cleaning is essential to ensure integrity of all safety equipment. Follow the cleaning
instructions below without deviation.
• Clean the scaffold hook by wiping it with a soft, lightly oiled cloth
• If this is not sufficient, use warm water with a mild pH neutral (pH 7) detergent, to clean off any
foreign matter. Dry thoroughly and lubricate moving parts with a suitable spray lubricant
• DO NOT under any circumstances use any abrasive materials, acids, basic detergents or solvents
• Disinfect parts that come into contact with the operator’s skin, using a disinfectant suitable for
the material of the equipment (see ‘Specification’). Strictly follow the disinfectant manufacturer’s
recommendations and procedures
• ALWAYS allow the equipment to dry naturally, keep it away from open fire or any other heat
source
Note:
This also applies to equipment that has become wet during use.
Lubrication
• Occasionally apply a small amount of a suitable spray lubricant, to the gate mechanism.
Afterwards, perform a thorough inspection as described in ‘Inspection procedure’
Transport
• ALWAYS transport this equipment inside a dedicated bag or suitable container that protects it
from mechanical damage and shields the equipment from high temperatures, humidity, UV
rays and chemicals
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
• Store at moderate temperature and humidity, away from direct sunlight or chemicals, inside a
dedicated, UV-proof bag or container
• Never place heavy objects on top of this equipment
Disposal
Service life and product obsolescence
WARNING:
Fall arrest equipment is designed to arrest a fall from height ONLY ONCE! If
subjected to an arrested fall, the equipment must be withdrawn from service and rendered
unusable.
Note:
The date on which the product is removed from the original packaging for the first time
becomes the ‘date of first use’, which should be recorded on the Inspection Record (see end of this
manual). The specified working life begins from this point.
• This equipment is subject to a maximum working life of 5 years from the recorded date of
first use, provided the product has been correctly stored, maintained and subjected to regular
inspections by a trained and competent person
• New equipment may be stored for a maximum of 5 years from the date of manufacturing as
indicated on the product, and will still give the potential 5-year working life - provided it remains
in the original manufacturer's packaging
Note:
Other reasons why the product may be considered obsolete include but are not limited to
changes of applicable standard, regulations or legislation, development of new techniques or
incompatibility with other equipment.
WARNING:
Remove fall arrest equipment from service if:
• it has been used to arrest a fall
• any damage is present
• identification is not evident (permanent markings are not legible or have been damaged/
removed)
• it exceeds its specified service life
• if its full service history is unknown
• you have any doubt as to its integrity
Contact
Legal Manufacturer: Toolstream Ltd
For Declaration of Conformity please visit www.silverlinetools.com
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web:
silverlinetools.com/en-GB/Support
Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Notified body:
CCQS UK Ltd
5 Harbour Exchange
London
E14 9GE, United Kingdom
Notified body number:
1105
WARNING:
If the product is re-sold outside the original country of destination, it is essential
the reseller shall provide instructions for use, periodic examination, maintenance and repair in the
language of the country in which the product is to be used.
254155_Manual.indd 9
11/12/2019 17:01
Содержание 254155
