Silicon Laboratories RS9116 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 92

Silicon Laboratories RS9116 Скачать руководство пользователя страница 66

RS9116 CC0 Connectivity Module Datasheet v1.0.10, December 2021

silabs.com

| Building a more connected world.

Rev 1.0.10

66

| Page

o

Wide input voltage range (3.0 to 3.6V) on pin VINBCKDC

o

Output

– 1.4V and 300mA maximum load on pin VOUTBCKDC

•

SC DC-DC

– Switching converter for Always-ON core logic domain

o

Wide input voltage range (3.0 to 3.6V) on pin UULP_VBATT_1 and UULP_VBATT_2

o

Output

– 1.05V

•

LDO SOC

– Linear regulator for digital blocks

o

Input

– 1.4V from LC DC-DC or external regulated supply on pin VINLDOSOC

o

Output

– 1.15V and 300mA maximum load on pin VOUTLDOSOC

•

LDO RF and AFE - Linear regulator for RF and AFE

o

Input

– 1.4V from LC DC-DC or external regulated supply on pin RF_AVDD

o

Output

– 1.1V and 20mA maximum load on pin VOUTLDOAFE

•

LDO FLASH - Linear regulator for internal Flash

o

Input - Wide input voltage range (3.0 to 3.6V) on pin VINLDO1P8. VINLDO1P8 is an internal pin that is
not terminated on the package, and it is not accessible.

o

Output - 1.8V and 20mA maximum load on pin VOUTLDO1P8

4.2.8.1

Output Voltage Ranges

Pin Description

Supply Voltage (V)

Min

Max

VOUTLDOSOC

1.05

1.2

VOUTLDO1P8

1.75

2.0

VOUTBCKDC

1.25

1.55

VOUTLDOAFE

1.0

1.21

UULP_VOUTSCDC

1.02

1.2

UULP_VOUTSCDC_RETN

0.715

1.2

Table 36. Min. and Max. specifications of various output voltages

The output voltages from the IC/module will be reflected as per specifications only after the firmware is loaded.

4.2.9 Low Power Modes

It supports Ultra-low power consumption with multiple power modes to reduce the system energy consumption.

•

Dynamic Voltage and Frequency Scaling

•

Low Power (LP) mode with only the host interface active

•

Deep sleep (ULP) mode with only the sleep timer active

– with and without RAM retention

•

Wi-Fi standby associated mode with automatic periodic wake-up

•

Automatic clock gating of the unused blocks or transit the system from Normal to LP or ULP modes

4.2.9.1

ULP Mode

In Ultra Low Power mode, the deep sleep manager has control over the other subsystems and processors and
controls their active and sleep states. During deep sleep, the always-on logic domain operates on a lowered supply
and a 32 kHz low-frequency clock to reduce power consumption. The ULP mode supports the following wake-up
options:

•

Timeout wakeup

– Exit sleep state after programmed timeout value.

«
...
64
65
66
67
68
...
»

Содержание RS9116





























































































Отзывы:

Нет отзывов