background image

M88 Evaluation Kit User Guide 

Front side connectors 

STO-DEV7227-HB Rev. 2.1 

10 

7

 

Front side connectors 

Figure 3. M88 Evaluation Kit front side connector placement. 

Name 

Type 

Description 

FREQOUT 

SMA female 

Synthonized frequency selectable through SW 5/10/20/25 MHz 

OUT1 -/+ 

SMA female 

Configurable low jitter frequency output. Use + for single ended. 

OUT2 -/+ 

SMA female 

Configurable low jitter frequency output. Use + for single ended. 

OUT3 -/+ 

SMA female 

Configurable low jitter frequency output. Use + for single ended. 

OUT4 -/+ 

SMA female 

Configurable low jitter frequency output. Use + for single ended. 

OUT5 -/+ 

SMA female 

Configurable low jitter frequency output. Use + for single ended. 

Port 1 

RJ45 with 
integrated LED 
and SFP slot 

Primary Gigabit Ethernet. Use either RJ45 or SFP. RJ45 supports 
Power over Ethernet.  

ToD/1PPS Out  RJ45 

ToD and 1 PPS according to G.703 V.11. 1 PPS in RJ45 same signal 
as 1 PPS Out on SMA. 

PPS Out 

SMA female 

Configurable PPS, default 1PPS 100ms positive pulse. 50 

Ω

 

Table 1. M88 Evaluation Kit front side connector descriptions. 

Port 1 

ToD/ 
1PPS 

Out 

Содержание M88




























Отзывы: