Silicon Graphics Rackable C2005 Family Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 42

Silicon Graphics Rackable C2005 Family Скачать руководство пользователя страница 31

Installing a Hard Drive into the Hard Drive Carrier

007-5717-002

21

Installing a Hard Drive into the Hard Drive Carrier

To install a hard drive into the hard drive carrier, perform the following steps after removing the
hard drive from the chassis:

1.

Place the hard drive carrier on a flat, stable surface such as a desk, table, or work bench.

2.

Slide the hard drive into the carrier with the printed circuit board side facing down (see

Figure 3-1

).

3.

Carefully align the mounting holes in the hard drive and the carrier. Make sure the bottom of

the hard drive and bottom of the hard drive carrier are flush.

4.

Secure the hard drive using all four screws (see

Figure 3-1

).

5.

Replace the drive carrier into the chassis. Make sure to close the drive carrier using the drive

carrier handle.

Figure 3-1

Inserting Hard Drive into Carrier

Use a hard, stable

surface when installing

the hard drive

2

4

4

SAS/SATA

hard drive

Hard drive

carrier

«
...
29
30
31
32
33
...
»

Содержание Rackable C2005 Family











































Отзывы:

Нет отзывов