Siko MSA111C Скачать руководство пользователя страница 2

Quick Start Guide

MSA111C · Date 

06.06.2016 · Art. 

No. 

88809 · Mod. 

status 

152/16

SIKO GmbH

Weihermattenweg 2
79256 Buchenbach

www.siko-global.com

Phone

: + 49 7661 394-0

Fax

: + 49 7661 394-388

Service

: [email protected]

MSA111C

Magnetic sensor

For detailed documentation please refer under  

http://www.siko-global.com/p/msa111c

General information

Prior to installation, including in hazard areas, read the Installation Instruc-
tion (download from the internet). It contains the safety instructions, hints 
and technical data to be observed during installation. Subject to change with-
out notice.

 Caution

In order to ensure reliable functioning of this product, take care to transport, 
store, position and mount it appropriately. Exercise care when you operate and 
maintain the device. Only properly qualified personnel is authorized to install 
and operate this product.

Safety information

It is important for safety reasons that you read and understand the below 
instructions before you install the system:

• 

Installation, connection, commissioning and maintenance shall be done by 
properly qualified personnel.

• 

It is the responsibility of the customer to ensure that the personnel con-
cerned read and follow the instructions and directions of this Guide and of 
the Installation Instruction.

• 

It is the responsibility of the customer to ensure that the magnetic sensor is 
correctly connected and configured.

• 

Only personnel specifically trained by SIKO shall execute repair and mainte-
nance work.

Mounting of the magnetic sensor

The sensor collects the absolute travel information of the encoded magnetic 
band MBA111. Arrows on the sensor must point in the same direction as the 
arrows on the magnetic tape.

The position of the sensor regarding the magnetic tape is exactly defined. When 
mounting, special care shall be taken to maintain an air gap between tape and 
sensor over the whole measurement distance whether the tape or sensor is 
moved or not.

With functional safety (SIL 2) the mounting kit (accessory SIKO art. no. 
"ZB3053") must be used. It makes possible acceleration of <100 m/s² (see EN 
61800-5.2 Table D16).

Mounting the magnetic strip

Stick the magnetic tape level to the mounting surface or the distance to be 
measured. Unevenness impairs measuring accuracy.

Mounting steps:

• 

Clean mounting surface 

1

 carefully.

• 

Remove protective film 

2

 of the adhesive strip 

3

.

• 

Stick down the magnetic strip 

4

.

• 

Clean surface of magnetic strip carefully.

• 

Remove protective film 

6

 of the cover strip 

5

.

• 

Fix cover strip (both ends should slightly overlap).

• 

Also fix cover strip's ends to avoid unintentional peeling.

 Notice!

The tolerance and gap measures must be observed over the whole measuring 
length.





Marking on 

strip

Marking of sensor

Travel direction









active side

<±1°

Travel direction

* When mounting the sensor, take care 

that its inclination will nowhere result 

in a band/sensor gap greater than 

max. 0.3 mm.

Electrical Installation

The location should be selected to ensure that no capacitive or inductive inter-
ferences can affect the sensor or the connection lines!

• 

All lines for connecting the magnetic sensor must be shielded.

• 

Wiring to the screen and ground (0 V) must be secured to a good point. 
Ensure that the connection of the screen and earth is made to a large sur-
face area with a sound connection to minimise impedance.

• 

When mounting the system keep a maximum possible distance from lines 
loaded with interference. Use screening shields or metallized housings.

• 

Contactor coils must be linked with spark suppression.

Connection

Pin

RS485

SSI

DRIVE-CLiQ with 
input KTY84

1

Adjust

Adjust

+UB

2

D+

D+

T

sens

+

3

D-

D-

0 V

4

nc

T-

TXN

5

+UB

+UB

TXP

6

/Sin

/Sin

nc

7

Sin

Sin

RXN

8

/Cos

/Cos

RXP

9

Cos

Cos

DÜA

10

Config

Config

T

sens

-

11

nc

T+

nc

12

0 V

0 V

DÜB

Pin

DRIVE-CLiQ

1

+UB

2

DÜA

3

RXP

4

RXN

5

0 V

6

TXN

7

TXP

8

DÜB

Technical data

Electrical data

Additional information

Operating voltage

4.5 ... 30 V DC

reverse polarity protected (RS485, SSI)

10 … 30 V DC

reverse polarity protected, SELV/PELV 
(DRIVE-CLiQ)

Power input

≤1.2 W

RS485, SSI

≤1.6 W

DRIVE-CLiQ



 



viewing side =plug-in side 

plug pin

viewing side =plug-in side 

plug pin

Отзывы: