1
2
3
4
long press for 3 seconds to eliminate/
return original sound.
SINGTRONIC.COM
5
6
7
8
10
12
11
19
20
21
22
23
24
13
14
15
16
17
18
9
USB storage device, SD memory card, Line input or
2.-
:Allows you to select between different audio sources:
Bluetooth.
3.- Start recording.
1.-
MUTE
: Press to mute the speaker.
11.-
Battery cover:
Unscrew this cover to access the battery
8.-
:
Set the loop mode of the songs to repeat one or repeat
10.-
0-9
: Select the song by number.
When inserting the batteries, make sure that the polarity is
5.-
VOL +/-
: USB/SD/MP3 player module volume controls.
6.- / : Play the previous song or next song.
9.-
EQ
: Allows you to select between different equalizations.
holder. Use two batteries type LR6-AAA, preferably alkaline.
correct.
all.
7.- : Start and pause playback.
4.- Play the recording.
1
4
7
2
5
8
0
3
6
9
EQ
REC
CH-
SCAN
VOL-
VOL+
CH-
MUTE
REC
PLAY
1
2
3
4
5
6
7
8
9
10
11.-
MIC IN
: Micro level input, 6.3 mm jack connector.
1.- Information screen
9.-
: Start and pause in playback.
2.- Connection port of TF memory cards.
receiver.
8.-
: Play the previous song.
10.-
: Play the next song.
4.- Connection port of SD memory cards.
5.-
:
Allows you to select between different audio sources: USB storage device, SD memory card, Line input or Bluetooth
6.-
:
Long press to start recording; short press playback the recording files. Recording function only works when the U-disk is
3.- Connection port of USB storage devices.
inserted.
7.-
:
Set the loop mode of the songs to repeat one or repeat all. Long press for 3 seconds to eliminate/return original sound.
13.-
ECHO
: Decrease or enhance the echo effect.
attenuated automatically when a signal is detected in the wireless microphone or the mic input.
18.-
DC IN 15 V
: Power input for the supplied power adapter.
17.-
VOLUME
: General volume control.
14.-
GT. VOL
:Volume control for the guitar input.
16.-
BASS
: Adjust the bass of the music.
internal or external power supply.
20.-
MIC PRI
: Enable or disable the microphone priority function. When it is in the ON position, the rest of the entries will be
-
LOW:
This indicator will glow when the battery level is low. Please charge the speaker immediately.
-
CHAR
: The indicator will glow when the speaker is charging.
-
FULL
: This indicator will glow when the battery is fully charged.
19.-
AUX INPUT
: Line level auxiliary input, 2 x RCA connector.
21.-
POWER
: Turn on the power, the power indicator light will be on, regardless of that the speaker uses an
12.-
MIC VOL
: Volume control for the handheld microphone.
15.-
TREBLE
: Adjust the treble of the music.
23.-
POWER
: On/Off switch of the portable amplifier.
24.-
GT. IN
: Entrance for guitar connection, connector jack 6.3 mm.
22.-
DC INPUT
: Connection terminals for DC 12V.
indicator light will turn green. When the batteries are low, the indicator light will turn red. Proceed then
2.-
Operation switch:
3 positions, ON, STANDBY (center position) and OFF. Put it in the ON position for
microphone will turn on immediately when it is turned ON. Before turning the microphone on or off, be
sure to set the amplifier and receiver volume to a minimum to avoid damaging the speakers due to
1.-
Operating indicator:
When the switch is set to the ON position or the central position (STANDBY), the
to replace the batteries with new ones.
its operation. Set the switch to the center position (STANDBY) to save battery power and the
excessive volume spikes.
preferably alkaline. When inserting the batteries, make sure that the polarity is correct.
3.-
Battery cover:
Unscrew this cover to access the battery holder. Use two batteries type LR6-AA,
Panel/rear plate/MP3 function and operation
Handheld/Headset Microphone
Remote Control
1
2
3
11
