Commission the EVCS
Eng. Opts.
System Healthy
Name List
>
Config
About...
Edit Phonebook
E
>
Extension 1
Extension 2
Extension 3
Extension 4
Extension 5
Press Engineer Mode button
(located on back of ECU-8 lid)
SigTEL
Compact
Note
: Before commissioning the system ensure that all equipment is fully installed, connected and wiring tested.
Check all handsets are on-hook and the ECU-8 shows ‘System Healthy’ status at its LCD display. Configure the system by following the flow chart below.
Naming Outstations
Select ‘Edit Phonebook’ option.
and
- highlights extension
ACCEPT - selects 1st character
and
- changes character
ACCEPT - moves to next character
HOLD - moves to previous character & exits
DIRECTORY - saves changes
At the ECU-8, with the handset on-hook, select the ‘Edit Phonebook’ option by following the flow chart below. With an operator at the ECU-8, go to
the first outstation turn and make a call. At the ECU-8 lift the handset and press the ACCEPT button. The outstation’s channel is opened for speech and
automatically selected for editing. Check audio quality of the line and inform the operator at the ECU-8 your position. They can edit the outstation
name directly (see Naming Outstations below). Repeat this process for all remaining outstations but to avoid confusion only call in from one outstation
at a time. Outstations can also be manually named if you are sure of its location (see Naming Outstations below).
Press Engineer Mode button
(located on back of ECU-8 lid)
>
Change PIN
System Opts
Harmonise Names
Reset Names
Factory Dfts
Config
: 1
: 0
: 3
: 13
System Updated
Auto Learn
SigTEL
Compact
System Healthy
SigTEL
Compact
Edit Phonebook
>
About...
Eng. Opts.
Config
System Cfg
Syst Cfg
System Healthy
>
Unit Count 1
Auto Learn
Syst Cfg
Unit Count 1
>
Auto Learn
Configure the system
4
HOLD
CALL/
ACCEPT
FUNCTION
DIRECTORY
SILENCE
BUZZER
1
2
3
CALL/ACCEPT = SELECT
HOLD = BACK TO PREVIOUS DISPLAY & LAMP TEST
FUNCTION (1) = EDIT EXT. NAMES & PIN CODE ENTRY
DIRECTORY (2) = SAVE CHANGES & PIN CODE ENTRY
SILENCE (3)
BUZZER
= SILENCE BUZZER & PIN CODE ENTRY
(4) = CANCEL EDIT EXT. NAMES & PIN CODE ENTRY
= SCROLL UP
= SCROLL DOWN
Using the ECU-8 keypad
2 of 2
Approved Document No. DAU0302001 Rev 1
SigTEL
Emergency Voice
Communication System
Errors and omissions excepted. No responsibility can be accepted by the manufacturer or distributors of this product for any misinterpretation of this instruction, or for the compliance of the system as a whole. The manufacturers policy is one of continuous
improvement and we reserve the right to make changes to product specifications at our discretion and without prior notice.
Change Security PIN Code
Connecting Mains and Batteries
See Fig 1 overleaf for mains cable type. Connect a suitable 230 Vac supply
to the ECU-8 via the base knockouts. Terminate the mains cable at the
Power Supply PCB (plug P2) and NOT to main earth chassis (see Fig 3 right).
For the emergency standby power supply, only use good quality, sealed
VRLA batteries. Position and connect two 12 Vdc, 7 Ah batteries to the
ECU-8 using the supplied battery connection leads (see Fig 4 right).
Pg17
Pg29
Set up Latch Faults
Pg30
Clear Recent Calls
Pg31
Set up Auto-Answer
Pg31
Add/Remove outstations
Pg27
Check audio quality and interactively name outstations
Pg27
Pg24
24V
battery connection
leads (supplied)
12V, 7Ah
+
–
+
–
GND
12V, 7Ah
A B
C D
12V, 7Ah
+
–
+
–
12V, 7Ah
ECU-8
Battery Connector
Exchange PCB
Power Supply
PCB
A B
C D
230 Vac
Mains Fuse
1 A HRC
L E N
Batt fuse
1 A (F)
Power Supply
PCB
To 3A fused spur
Cable gland
Power Supply loom
Battery
Connector
P2
Power Supply
PCB
ECU-8
Exchange PCB
Fig 3
Fig 4
- No. ECU-8 units (should be set to 1)
- No. ECU-8NT units (networked systems only)
- No. Type A (fire telephone) outstations
- No. Type B (disabled refuge) outstations
What the symbols mean
Additional System Set up Features
Check the unit count
(number of ECU-8) is set to 1
Pg22
Check the number of ECU-8 and
outstations match the number
connected on the system
Observe correct polarity!
DO NOT press the
Reset button!
