background image

2

READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN
RESULT IN SERIOUS PERSONAL INJURY.

STRAP BREAKAGE HAZARD
Improper operation of the tool or sharp corners on the load can result in strap
breakage during tensioning, which could result in the following:

!

A sudden loss of balance causing you to fall.

!

Both tool and strap flying violently towards your face.

Failure to place the strap properly around the load or an unstable or shifted load could result in a
sudden loss os strap tension during tensioning. This could result in a sudden loss of balance
causing you to fall.

!

If the load corners are sharp use edge protectors.

!

Positioning yourself in-line with the strap, during tensioning and sealing, can result in severe
personal injury from flying strap or tool. When tensioning or sealing, position yourself to one
side of the strap and keep all bystanders away.

TRAINING
This tool must not be used by persons not properly trained in its use. Be certain that you receive
proper training from your employer. If you have any questions contact your Signode
Representative.

EYE INJURY HAZARD
Failure to wear safety glasses with side shields can result in severe eye injury or
blindness. Always wear safety glasses with side shields which conform to ANSI
Standard Z87.1 or EN 166.

FALL HAZARD
Maintaining improper footing and/or balance when operating the tool can cause you to fall. Do
not use the tool when you are in an awkward position.

CUT HAZARD
Handling strap or sharp parts could result in cut hands or fingers. Wear protective
gloves.

TOOL CARE

!

Inspect and clean the tool daily. Replace all worn or broken parts.

!

Lubricate all moving parts weekly unless otherwise specified.

!

On air powered tools, always disconnect the pneumatic connection to the tool when
performing part removal and replacement procedures. NEVER connect a pneumatic source to
a disassembled tool unless otherwise specified.

WORK AREAS
Keep work areas uncluttered and well lighted.

Содержание PN2-114





















Отзывы: