background image

3

2350 Temperature Sensor

+

-

3-8052

3-8050.521

Loop Input +

4 to 20 mA

loop monitor

Power Supply

DC 12 - 24 V

Black (Loop +)

Optional

Earth Ground

Loop Input -

Shield

White (Loop - )

Red

•  Connect the 2350 cable directly to a loop device as shown.

4. Digital 

(S

3

L) Wiring

•  All models of the 2350 provide Digital (S

3

L) output when powered with 5 VDC.

•  Connecting the SHIELD to a direct Earth ground may reduce electrical noise interference.
•  The maximum Digital (S

3

L) cable length is dependent upon the instrument to which the sensor is connected. Consult the instrument 

manual for details.

•  Connect the 2350 cable directly to 

Digital (S

3

L) I/O terminals.

•  When the 2350 includes a junction 

box, connect the 2350 terminals to any 
Digital (S

3

L) I/O port as shown.

•  When the 2350 includes a junction box, connect the 2350 

terminals to a loop device as shown.

5.  4 to 20 mA Loop Wiring

•  The 2350-3 provides a 4 to 20 mA loop output when powered with 24 VDC.
•  Connecting the SHIELD to a direct Earth ground may reduce electrical noise interference.
•  Red wire is not used, do not remove the heat shrink. See Section 6, 4 to 20 mA Span Adjustment.

5.1  Current Loop With No Junction Box

5.2  Current Loop With Junction Box

3-8052-1

+

-

4-20

mA

FREQ/

DA
T

A

WHT

W
HT

BLU

B

LK

N/C

R

ED

SHIELD

SENSOR

INPUT

SHIELD

+

FREQ/

DA
T

A

+

-

White

Black

Power Supply

DC 12 - 24 V

Loop Input

Loop Input

DATA

GND

SHLD

V+

3-8052-1

4-20

mA

FREQ/

DA
T

A

WHT

W
HT

BLU

B

LK

N/C

R

ED

SHIELD

SENSOR

INPUT

SHIELD

+

FREQ/

DA
T

A

3-8052

3-8900.621C

I/O Module 3-8900.401-X

1

2

3

4

5

6

7

8

9

10

11

12

13

14

+5VDC (Black)

Freq. Input (Red)

GND (Shield)

+5VDC (Black)

Freq. Input 2 (Red)

S  L (Red)

GND (White/Shield)

+5VDC (Black)

S  L (Red)

GND (White/Shield)

3

3

Analog Output 1

Analog Output 2

(if applicable)

(if applicable)

Frequency

Input

1

Frequency

Input 2

OR

S3L

Input

2

S3L

Input

1

+

-

+

-

7
6
5

GND

V+

IN

Black

Red

Shield

White

Optional

Earth ground

3-9900
S

3

L connector

3-8900
I/O Module Connector

Black

Red

White

White
Black
Red

3-8350
Temperature Transmitter

Black

Red

White

Shield

Содержание 2350

Страница 1: ... Cable type 3 cond shield 22 AWG Standard cable length 4 6 m 15 ft Shipping weight 0 22 kg 0 5 lb Electrical Power requirements S3 L models 5 VDC 10 1 5 mA 4 to 20 mA models 12 24 VDC 10 Short circuit reverse polarity protected Digital S3 L output Serial ASCII TTL level 9600 bps Accuracy 0 5 C 0 9 F Repeatability 0 1 C 0 2 F Resolution 0 01 C 0 02 F Update rate 100 ms 4 to 20 mA output Accuracy 32...

Страница 2: ...the process connection Make sure the flow alignment indicator is in correct position in the pipe Damage to the sensor tip can occur if the sensor tip is installed improperly Install 8350 transmitter or 9900 refer to 8350 or 9900 manual for wiring information The 3 8052 Integral kit includes 3 4 in NPT process connection 3 9000 392 1 liquid tight connector 1 2 in NPT Conduit base to attach 8350 3 3...

Страница 3: ...0 mA loop output when powered with 24 VDC Connecting the SHIELD to a direct Earth ground may reduce electrical noise interference Red wire is not used do not remove the heat shrink See Section 6 4 to 20 mA Span Adjustment 5 1 Current Loop With No Junction Box 5 2 Current Loop With Junction Box 3 8052 1 4 20 mA FREQ DATA WHT WHT BLU BLK N C RED SHIELD SENSOR INPUT SHIELD FREQ DATA White Black Power...

Страница 4: ...signet com Or call in the U S 800 854 4090 For the most up to date information please refer to our website at www gfsignet com 3 2350 090 1 Rev K 03 13 English Georg Fischer Signet LLC 2013 WARNING Not protecting the red wire may cause the 4 to 20 mA span to be reset Wire Nut With power applied as described in Section 5 connect the RED wire to the WHITE wire for 15 seconds After about 10 seconds t...

Отзывы: