SignalFire Sentinel-485-2DI Series Скачать руководство пользователя страница 2

Страница: 2 / 13

SignalFire Telemetry

Rev 1.3

Specifications

Enclosure Size

3.5” tall

5.0” wide

5.0” deep

Power Source

Internal IS Lithium battery pack

SignalFire Part Number: 3BIS

External Solar battery system

SignalFire Part Number: Sentinel-HCSolar

DC-DC Converter

SignalFire Part Number: DCDC-Sentinel

Other external power supply meeting the power entity parameters from the
control drawing.

Temperature Rating

-40°C to +60°C

Radio Frequency

902-928MHz Ism Band, FHSS radio, internal antenna

Compliance

Temperature Accuracy

Certified for use in Class I, Division 1 groups C and D. EXi [EXi]
FCC/IC Certified

+/- 0.5°C

WARNING: Use of this equipment in a manner not specified by the manufacturer may
impair the protection provided by the equipment.

WARNING: The use of any parts not supplied by the manufacturer violates the safety rating
of the equipment.

The associated apparatus provides intrinsically safe outputs.

L’appareil associ

é fournit des sorties à sécurité intrinsèque.

Refer to control drawing

“Sentinel –

Control Drawing

–

Modbus, Thermocouple, RTD, and Float Stick”

for

requirements when used in a Class I Division 1 area.

Содержание Sentinel-485-2DI Series














Результаты поиска

Содержание Sentinel-485-2DI Series

Отзывы:

Бренды по названию

Популярные бренды

SignalFire Sentinel-485-2DI Series, Инструкция по интерфейсу

Результаты поиска

Содержание Sentinel-485-2DI Series

Отзывы:

Бренды по названию

Популярные бренды