Sierra Wireless MP 700 Series Скачать руководство пользователя

Страница: 85 / 118

Command Reference

Rev 3.2 Oct.05

+CNMI (continued)

New SMS message indications (continued)

<ds>

may be one of two values:

•

<ds>=0:

No SMS-STATUS-REPORTs returned

•

<ds>=1:

SMS-STATUS-REPORTs returned:

+CDS: <length><CR><LF>

(PDU mode enabled)

+CDS: <fo>,<mr>,[<ra>],[<tora>],<scts>,<dt>,<st> (text mode enabled)

+<bfr>

may be one of two values:

•

<bfr>=0:

The modem’s buffer of unsolicited result codes is flushed to the

computer when

<mode>=1

, or

is entered. (

is returned before

flushing the codes.)

•

<bfr>=1:

The modem’s buffer of unsolicited result codes is cleared when

<mode>=1

, or

is entered.

Note: See

+CMGL

(page 78–79) and

+CMGR

(page 79) for details on the

listed parameters.

+CNUM

Retrieves the MSISDN from the SIM

Retrieves the MSISDN (Mobile Station International ISDN), or mobile phone
number, from the SIM.

The MSISDN can be edited in user interface software such as Watcher (the
AirCard enabling software).

Response parameters

The response to the +CNUM command has these parameters:

+CNUM:[<alpha>],<number1>,<type1>[,<speed>,<service>[,<itc]]
[<CR><LF>+CNUM:[<alpha2>],<number2>,<type2>[,<speed>,<service>
[,<itc>]][...]]

<alpha

is an optional alphanumeric string associated with

. (This

can be edited in the user interface software (such as Watcher, the AirCard
enabling software). (The character set used is that set with the command

+CSCS

. See page 93.)

<number

is a string type phone number of the format specified by

<typex>

<type

is the type of octet in integer format. (Refer to GSM 04.08 subclause

10.5.4.7. This specification is listed on page 8.)

Continued on next page.

Table 3-9: Command Reference Table (ASCII Alphabetic)

Command

Description

Содержание MP 700 Series























































































































Результаты поиска

Содержание MP 700 Series

Отзывы:

Похожие инструкции для MP 700 Series

Бренды по названию

Популярные бренды

Sierra Wireless MP 700 Series, Справочник по командам

Результаты поиска

Содержание MP 700 Series

Отзывы:

Похожие инструкции для MP 700 Series

Бренды по названию

Популярные бренды