manualshive.com logo in svg

Sierra Wireless AirPrime WP8548, Руководство по интеграции оборудования

Поделиться
Скачать
Sierra Wireless AirPrime WP8548 Скачать руководство пользователя страница 23

Regulatory Compliance and Industry Certifications

Rev 2  Feb.16

23

Specifications subject to change

5.

A label must be affixed to the outside of the end product into which the 
AirPrime WP8548 module is incorporated, with a statement similar to the 
following:

· This device contains FCC ID: N7NWP8 / IC:2417C-WP8.

6.

A user manual with the end product must clearly indicate the operating 
requirements and conditions that must be observed to ensure compliance 
with current FCC / IC RF exposure guidelines.

The end product with an embedded AirPrime WP8548 module may also need to 
pass the FCC Part 15 unintentional emission testing requirements and be 
properly authorized per FCC Part 15.

Note:  If this module is intended for use in a portable device, you are responsible for 
separate approval to satisfy the SAR requirements of FCC Part 2.1093 and IC RSS-102.

Содержание AirPrime WP8548



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды