Sierra Wireless AirLink FX100 Скачать руководство пользователя

Страница: 67 / 114

4112221

Rev 7.2

June 19, 2013

User Guide

Communicating with the FX Series

9.2.

Verifying the Received Signal Strength

The FX Series only establishes a call if the received signal strength is strong enough. Using a
communication software such as HyperTerminal, enter

AT+CSQ

to check the received signal strength.

The response returned will follow the format

+CSQ: <rssi>, <ber>

where:

<rssi> = received signal strength indication, and <ber> = channel bit error rate.

Refer to the table below for the description of the <rssi> values returned.

Table 50.

<rssi> Value Description

<rssi> Value

Description

– 10

Received signal strength is insufficient

– 31

Received signal strength is sufficient

– 98

Not defined

No measure available

9.3.

Verifying the Network Registration

Using a communication software such as HyperTerminal, enter

AT+CREG?

to verify the network

registration of the FX Series. Refer to the table below for the list of main responses returned.

Table 51.

AT+CREG? Main Reponses

AT+CREG? Response

Description

AT+CREG: 0, 0

Not registered

AT+CREG: 0, 1

Registered on the home network

AT+CREG: 0, 5

Registered on a roaming network

If the FX Series is not registered on the network, do the following:



Check the connection between the FX Series and the antenna.



Verify the signal strength to determine the received signal strength (Refer to section 9.2
Verifying the Received Signal Strength).

9.4.

Checking the Band Selection

Using a communication software such as HyperTerminal, enter

AT+WMBS?

to check the band

selection of the FX Series. Refer to the table below for the list of main responses returned.

Table 52.

AT+WMBS? Main Reponses

AT+WMBS? Response

Description

AT+WMBS: 0, x

Mono band mode 850MHz is selected

AT+WMBS: 1, x

Mono band mode extended 900MHz is selected

AT+WMBS: 2, x

Mono band mode 1800MHz is selected

AT+WMBS: 3, x

Mono band mode 1900MHz is selected

AT+WMBS: 4, x

Dual band mode 850/1900MHz is selected

Содержание AirLink FX100



















































































































Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды

Sierra Wireless AirLink FX100, Руководство пользователя

Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды