background image

Siemens Industry, Inc.
Building Technologies  Division

P/N 315-048670-11

7

Care must be taken when installing the zone input and zone output field wiring to

prevent possible cross wiring. This can cause severe damage to the system when

powered up or when zone is activated.

 The screw terminals can accommodate one 12-18 AWG or two 16-18 AWG.

If the total output of all 8 zones exceeds 12 amps, a single PSC-12 cannot be used to

supply the ZIC-8B. Refer to the PSC-12 Installation Instructions, P/N 315-033060 for

information when the total system load exceeds 12 amps.

INSTALLATION

The ZIC-8B plugs perpendicularly into one slot in the CC-5/CC-2 card-cage via two 96-
pin DIN connectors and can occupy any slot in the card cage. (Refer to Figure 4.)

Insert the ZIC-8B card into the card guides right side up (lettering on the front panel
is legible)

Slide the card in until the card edge connectors contact
the receptacles on the motherboard.

Verify that the DIN connectors of the card and the card-
cage aligned properly. The card can only plug in one
direction to the card cage, if it does not align, DO NOT
FORCE the card.

Place thumbs on the front panel adjacent to the captive
screws and gently apply even pressure on the card
until the connectors seat in the receptacles on the
motherboard.

Secure with the captive screws.

Power up the system and verify that the ZIC-8B power
LED turns ON.

ELECTRICAL RATINGS

Figure 4

Installing The  ZIC-8B

24V Back Plane or

External Power Current

See NOTE below

Screw Terminal 24V Current

Total Device Current

6.2V Back Plane Current

0

24V Standby Current

105mA

NOTE:  

The 24V current is dependent on the usage and wiring

type of each ZICCkt of the ZIC-8B. Listed below are the required

current draws for each zone usage and wiring type.

ZIC-8B Current Requirement

Per Output Zone

Zone Usage

Output Current

Requirement

Not Used

0

NAC

17mA

Strobe - Sync.

17mA

Strobe - Unsync.

17mA

Speaker Zone - 2 Ch.

34mA

Speaker Zone - 1 Ch.

17mA

NAC - Coded

17mA

ZIC-8B Supervisory State Standby Current =91mA

Содержание ZIC-8B













Отзывы: