8
Installation
Scope of delivery: dryer, installation and instruction manual, basket for woollens
(depending on the model).
Check dryer for transport damage.
The dryer is very heavy. Do not lift without assistance.
Be careful to avoid sharp edges.
Do not install in a room which is susceptible to frost. Water may cause damage once it
starts to freeze.
If in doubt, have the appliance connected by a specialist.
Do not lift the dryer by any of the protruding parts (e.g. the door) as they may break off.
Setting up the dryer
The appliance plug must always be accessible.
Ensure that the appliance is installed on a clean,
level and firm surface.
Do not obstruct the air inlet on the front of the
dryer.
Keep the area around the dryer clean.
Level the dryer using the threaded feet.
Use a spirit level.
Do not remove the threaded feet under any
circumstances.
Mains connection
see safety information
a
Page 13.
Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist.
The mains voltage and the voltage shown on the rating plate (
a
Page 10
) must be the
same.
The connected load and necessary fuse protection are specified on the rating plate.
Frost protection
Preparation
1. Empty the condensation container
a
page 4
.
2. Select any programme using the programme selector.
3. Press the
Start
/Stop button
a
condensation is pumped into the container.
4. Wait 5 minutes and then empty the condensation container again.
5. Turn the programme selector to
Off
.
Transport
Preparation of dryer
a
see Frost protection.
Transport the dryer in a vertical upright position.
Following transportation, leave the dryer to stand for two hours.
There may be residual water in the dryer.
This can leak out if the dryer is at an angle.
1.
Remove all accessories
from the drum.
The drum must be empty.
Make sure that the air inlet
remains unobstructed
Clean and level
Do not install the dryer behind a door or sliding
door, which could prevent or restrict opening of the
dryer door. This will prevent children from locking
themselves in and putting their lives in danger.
2.
Do not operate the dryer if
there is a danger of frost.
9
Only when the appliance is
switched off.
Care and cleaning
Heat exchanger
The heat exchanger of the dryer is cleaned automatically when drying is in progress,
Cln
appears in the display panel. Do not pull the condensation container out during the cleaning
process.
Dryer housing, control panel, air intake
Wipe with a soft, damp cloth.
Do not use harsh cleaning agents or solvents.
Remove detergent and cleaning agent residue immediately.
Some water may collect between the window and the seal during drying. This does not affect
the proper operation of your dryer in any way.
Filter in the condensation tank
The filter is cleaned automatically when the condensation container is emptied.
However, the filter should still be cleaned regularly under running water. This prevents stubborn
deposits/dirt from building up.
Cleaning is only required if the symbol
ā
flashes again in the display panel after the
condensation container has been emptied.
1.
Pull out the condensation container.
2.
Pull the filter out of its snap-in lock.
3.
Clean the filter under running water or in the dishwasher.
4.
Refit the filter.
5.
Insert the condensation tank so that it locks into place.
Only operate the dryer with the filter inserted.
Moisture sensor
The dryer is equipped with stainless-steel moisture sensors. These measure how damp the
laundry is. After long periods of use, a fine layer of limescale can form on the moisture
sensors.
1.
Open the door.
2.
Clean the moisture sensors using a damp sponge with a rough surface.
Do not use steel wool or other abrasive materials.
ʠ
ʠ
ʠ
a
ʠ
ʠ
ā
a
a
ʠ
4
a
ʠ
ʠ
ʠ
ʠ
a
a
a
a
ʠ
a
a
a
a
a
ʠ
ʠ
ʠ
ʠ
ʠ
a
ʠ
a
a
a
a
a
a
a
a
a
a
a
a
a
