Siemens TX-I/O Скачать руководство пользователя | Manualshive

Страница: 56 / 94

background image

56 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

4.12 Continuous 3-Point Analog Output

AO_Y250T_2Cha_1_Open

(SIMATIC Manager hardware catalog)

AO_Y250T_2Cha_2_Close

(SIMATIC Manager hardware catalog)

Continous 3-point analog output with two channels for positioning drives.

This function is used for the open/close control of three-position drives without
feedback (without a position potentiometer) – for example, for



valve drives



Damper actuators



Third-party drives

4.12.1 Function

The function uses two channels. These must



be in the same module and



follow in direct succession.

An internal stroke model (path algorithm) [StrkPos] calculates the required length of
the open or close pulses from the drive cycle time and the position defined by the
process value. No feedback is required by the drive.

The function supports

asymmetric drives

with different opening and closing cycle

times under the condition that this is also supported by the automation station.

AO_Cont3Point_Simple

SIMATIC HW catalog

Description

AO_Y250T_2Cha_1_Open

'Open' channel for the AO_Cont3Point_Simple function

AO_Y250T_2Cha_2_Close

'Close' channel for the AO_Cont3Point_Simple function

The function converts the process value [AOValue] to a 3-position signal. A stroke
model [StrkPos](path algorithm) continuously simulates the position of the drive
based on the incoming control commands, and calculates the required length of
the open and close pulses from the drive cycle time and the position defined by the
process value. It therefore represents the drive position at all times. As a result, the
drive does not require corresponding feedback signals.

For full integration of all of the functionality – including the resulting stroke position
[StrkPos] and the function status [FncSta] – the 'Cluster Object Model' must be
applied (as described in PD622-F-0012 – Architectural Concepts).

4.12.2 Backup Mode

Function for control of the behavior of the function when changing to the
'MasterDown' status.

Possible values

Description

NO

Process value = INACTIVE, 0 (Off)

VALUE

Specific value of the parameter [BOBackupValue]

KEEP

Save the last active process value

4.12.3 AO Backup Value

Representation

Definition,

addition

Positioning model

Full functionality

Definition,

addition

«
...
54
55
56
57
58
...
»

Содержание TX-I/O































































































Отзывы:

Нет отзывов

Похожие инструкции для TX-I/O

Бренд: ABB Страницы: 58

Бренд: ABB Страницы: 191

Бренд: National Instruments Страницы: 8

PROX-BOOSTER 2G

Бренд: Nedap Страницы: 25

Бренд: WaterLogic Страницы: 29

Бренд: WaterCop Страницы: 4

Бренд: M-system Страницы: 4

Бренд: JBL Страницы: 8

Бренд: M-system Страницы: 9

Ezi-IO EtherCAT DA

Бренд: Fastech Страницы: 52

Бренд: Data Aire Страницы: 137

Бренд: Ravaglioli Страницы: 102

Бренд: ViziT Страницы: 5

Бренд: Fermax Страницы: 16

Бренд: Commax Страницы: 11

Бренд: D-Box Страницы: 12

Бренд: Nußbaum Hebetechnik Страницы: 32

Бренд: QUALITY LIFTS Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды