Siemens TPS4 13 Скачать руководство пользователя

Страница: 11 / 12

Dry Contact

Three 3' 18 AWG wires are included through the nipple as the Dry Contacts.

• Please note: Dry Contacts are designed for low voltage or control signals only.

•

Maximum

switching

current

• Maximum switching voltage is 240V DC or AC.

• Higher energy applications require additional relay implementation outside the SPD.

• Gray is Common, Blue is Normally Open and Red is Normally Closed. If the Dry Contacts are not utilized,
insulate lead ends, coil and secure.

Maintenance

SPDs require minimal maintenance. We recommend periodic inspection of diagnostic indicators to ensure
proper operation. We also recommend keeping the SPD clean as appropriate.

Troubleshooting and Service

Please contact Siemens Technical Support for any service related issues. We want to take care of any
problems.

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

TPS4 13

Содержание TPS4 13













Результаты поиска

Содержание TPS4 13

Отзывы:

Похожие инструкции для TPS4 13

Бренды по названию

Популярные бренды

Siemens TPS4 13, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание TPS4 13

Отзывы:

Похожие инструкции для TPS4 13

Бренды по названию

Популярные бренды