Siemens TLX Скачать руководство пользователя | Manualshive

Страница: 21 / 21

background image

Wireless Transceiver Tool (TLX) (For WFLN Version 1)

TLX Error Messages

Table 5 shows the error messages supported by the TLX. Many of the errors may occur due to high
network traffic and can be fixed by trying the TLX command again.

Table 5.

TLX Error Messages.

Error Message

More Information

Specified node not present on Wireless FLN.

This error indicates the specified FPX or FLNX was not
found on the WFLN.

Verify that the Network ID is correct and the node
devices are powered up and connected properly.

Multiple FLNX nodes on Wireless FLN have specified
EUID.

Generally, this error occurs if the partial EUID that was
entered was not unique.

Use more characters in the partial EUID to find a unique
match.

Invalid command.

Enter the command again. Although the commands
are not case-sensitive, be sure that spaces are used
correctly and there are no trailing characters.

Unable to retrieve configuration data from specified
node.

Enter the command again. The network might have
been temporarily busy.

Unable to retrieve binding table at the specified node.

This error can occur if the response message does not
return within five seconds or the TLX was unable to
retrieve a local binding table entry.

Also, the network might have been temporarily busy.

Try entering the command again.

Unable to get binding table entry.

Enter the command again. The network might have
been temporarily busy.

Unable to get link costs at the specified node.

Enter the command again. The network might have
been temporarily busy.

Unable to perform energy scan at the specified node.

Enter the command again. The network might have
been temporarily busy.

Unable to initiate reboot at the specified node.

Enter the command again. The network might have
been temporarily busy.

Unable to get link qualities at the specified node.

Enter the command again. The network might have
been temporarily busy.

Unable to get link RSSI values at the specified node.

Enter the command again. The network might have
been temporarily busy.

Revision Date: June 20, 2006

21

CONFIDENTIAL: For Internal Use Only

Siemens Building Technologies, Inc.

«
...
19
20
21

Содержание TLX






















Отзывы:

Нет отзывов

Похожие инструкции для TLX

Бренд: Lamtec Страницы: 80

Бренд: Ebode Страницы: 24

Бренд: R&S Страницы: 70

Бренд: Garmin Страницы: 6

Бренд: RadioMaster Страницы: 2

Бренд: Panlux Страницы: 2

Бренд: Harman Kardon Страницы: 42

Бренд: ABBA Страницы: 8

Бренд: AMG Страницы: 8

Bearcat BC 210XLT

Бренд: Uniden Страницы: 10

RF24V1PR-ASL-NIS

Бренд: GAMA Electronics Страницы: 4

Бренд: Erreka Страницы: 4

Бренд: Onkyo Страницы: 81

Бренд: Icom Страницы: 16

Бренд: Zero88 Страницы: 14

Бренд: Black Box Страницы: 2

Бренд: IDS Страницы: 2

Бренд: Yaesu Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды