Siemens Synco living Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 100

background image

60 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

You operate a switching group defined as

Scene

under:

Main menu > Switching groups > Switching group X > Scene A or B
> Trigger scene:

The text displays for scenes A and B can be adjusted to suit your
needs (refer to page 60).

Scenes

When commissioning the plant, the softkeys of the central apartment unit
(switching groups 1 – 4) can be programmed for triggering scenes (scene
symbol appears on the display of the key assignment).

Scenes can be used to store certain states of all actuators involved and to
retrieve them again, if desired.
One example would be the differently dimmed lights and the blind positions
that you would consider adequate for a certain event / at certain times.

Creating scenes

For the switching groups, a scene A and scene B can be created.
Enter the required name of the scene at the central apartment unit:

Main menu > Switching groups > Switching group X > Scene A or B
> Scene A or B:

Then, use local actuator control to drive all actuators to the required position.

After that, store the scene by pressing the respective softkey for at least
3 seconds. Storage is confirmed by the central apartment unit in the form of a
short acoustic signal.

You trigger the stored scenes by a short push on the respective softkey.

The scenes can also be stored and retrieved via operating parameters:

Main menu > Switching groups > Switching groups X > Scene A or B
> Trigger scene:

Triggering switching groups via an event

In addition to manual triggering, the function of a switching group can be
automatically triggered via one or several events.

Select the event (or the events) that triggers a switching group configured for

Switch

or

Dim

:

Main menu > Switching groups > Switching group X > Events on cmd:

Main menu > Switching groups > Switching group X > Events off cmd:

«
...
58
59
60
61
62
...
»

Содержание Synco living





































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco living

Бренд: Ohsung Electronics Страницы: 18

Бренд: IDS Страницы: 2

Бренд: RADEMACHER Страницы: 68

GECO LUX GECO60

Бренд: GiBiDi Страницы: 48

Бренд: YASKAWA Страницы: 340

Бренд: TWR Lighting Страницы: 49

Бренд: Apricus Страницы: 32

Бренд: Forcepoint Страницы: 15

VPPM-...-LK Series

Бренд: Festo Страницы: 4

Бренд: SMC Networks Страницы: 12

Бренд: Rain Bird Страницы: 11

Бренд: Equalizer Страницы: 26

LOOPDRIVE FIM-RC

Бренд: 4EVAC Страницы: 2

Бренд: H3C Страницы: 16

Бренд: Yale Страницы: 2

Бренд: Nedap Страницы: 5

Бренд: Water Specialist Страницы: 60

Бренд: aerl Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды