Siemens SIWAREX MS Скачать руководство пользователя страница 22

Страница: 22 / 75

Hardware

Configuration and Assembly

3. Twisted pair cables should be used for the specified lines and should also be
shielded:

- Sensor line SEN+ and SEN-

- Measuring voltage lines SIG+ and SIG-

- Supply voltage lines EXT+ and EXT-

We recommend using the cable indicated in chapter

10 Accessories

4. The shielding must be connected to the shielding connection clamp.

The maximum distance between the SIWAREX MS and the load cell is applicable
when using the recommended cables.

The power supply (6V) for the load cells comes from the SIWAREX MS. (terminal
EXC+ and EXC-).

The connection should be made using the cable indicated in chapter

10 Accessories

Connection and signal designations

Comment

SEN+ Sensor

line

SEN-

Sensor line -

SIG+

Measurement line +

SIG-

Measurement line -

EXC+

Load cell supply

EXC-

Load cell supply output -

Table 4-2

Load cell connections

4-14 SIWAREX

Содержание SIWAREX MS












































































Результаты поиска

Содержание SIWAREX MS

Отзывы:

Похожие инструкции для SIWAREX MS

Бренды по названию

Популярные бренды

Siemens SIWAREX MS, Руководство по эксплуатации устройства

Результаты поиска

Содержание SIWAREX MS

Отзывы:

Похожие инструкции для SIWAREX MS

Бренды по названию

Популярные бренды