manualshive.com logo in svg

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Поделиться
Скачать
Siemens SIWAREX FTC Скачать руководство пользователя страница 85

W

EIGHING 

F

UNCTIONS AND 

P

ARAMETERS

 

Name 

Type 

Address 

Default 

Range of Values / Meaning 

Reference 

If 0, the continuous operation 

Maximum loading time 
 

TIME DBD004  0  0: 

deactivated 

>100: time f. Monitoring the maximum loading 
time. 

5.14.2 

Trailing weight 

REAL 

DBD008 

0 

Quantity that still must be dosed after reaching 
the set value  

5.14.3 

Reserve_21_12 
 

REAL DBD012 

0  Reserved 

 

Log selection 

BYTE 

DBB016 

0 

0: 

No automatic logging 

                performed 
1: 

autom. logging with text 1 

2: 

autom. logging with text 2 

3: 

autom. logging with text 3 

4: 

autom. logging with text 4 

5.14.4 

Reserve_21_17  
 

BYTE DBB017 

0  Reserved 

 

  

18 

 

 

 

Table 5-12 

Allocation of DR 21 

5.14.1  DR 21 – Loading quantity 

The total quantity for loading operation can be set using this parameter. 

The belt is stopped when the total quantity is achieved in totalizing memory 

1 and the totalizing is ended. For loading the predefined quantity again, 

totalizing memory 1 must be deleted. 

5.14.2  DR 21 – Maximum loading time 

The maximum loading time is started as well when loading is started. If the 

total quantity is not achieved before this time has elapsed, SIWAREX FTC 

sends out a technology message.  

5.14.3  DR 21 – Trailing weight 

The trailing weight is the material quantity that must be weighed in addition 

after the set value has been reached.. 

5.14.4  DR 21 – Log Selection 

After the total quantity has been reached, a log can be created 

automatically. One of four log text messages can be defined with this 

parameter. 

 

5.15  DR 30 Process Status 1 (NAWI, Force measurement, Belt scale)  

The process values and the expanded process values can be used to monitor the 
current states and data in the non-automatic weighing instrument. Observing the 
selected data is very helpful in test operation for optimizing parameters. The status 
can also be monitored if the SIWAREX FTC is controlled by the SIMATIC CPU. 

The NAWI- and Conti-status flags are simultaneously updated in DR 32 as well - 
process status loss-in-weight scale. 

 

Name

 

Type 

Address  Range of Values / Meaning 

Reference

NAWI status flags 

DINT 

DBD000 

Status bits (see below) 

5.15.1 

SIWAREX FTC 

5-73 

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды