Siemens sitrans tr300 Скачать руководство пользователя страница 49

Страница: 49 / 96

Functions

9.12 Alarm current

SITRANS TR200/TR300

Operating Instructions, 06/2010, A5E01071992-03

9.12

Alarm current

This function is used to set the magnitude of the alarm current. The alarm current signals a

sensor fault or a hardware/firmware fault.
The intensity of the alarm current can be freely selected within the preset limits of the current

control range of 3.6 mA to 23 mA. The upper and lower limit of the linear control range can

also be freely selected within the preset limits of the current control range of 3.6 mA to 23

mA.
One example of this is shown in the following diagram. The specified accuracy values of the

output signal only apply to the corresponding nominal ranges.

0HDVXULQJUDQJH

>P$@

7>@

①

Linear control range

②

Lower limit of the control range (default value = 3.80 mA)

③

Upper limit of the control range (default value = 20.5 mA)

④

Lower fault current value (default value = 3.6 mA)

⑤

Upper fault current value (default value = 22.8 mA)

⑥

Recommended setting range for lower fault current range and lower control range limit

⑦

Recommended setting range for upper fault current range and upper control range limit

Figure 9-1

Current limits with output signal 4 to 20 mA

Содержание sitrans tr300

































































































Результаты поиска

Содержание sitrans tr300

Отзывы:

Похожие инструкции для sitrans tr300

Бренды по названию

Популярные бренды

Siemens sitrans tr300, Руководство пользователя

Результаты поиска

Содержание sitrans tr300

Отзывы:

Похожие инструкции для sitrans tr300

Бренды по названию

Популярные бренды