Siemens SITRANS LVL200E Скачать руководство пользователя страница 39

Страница: 39 / 44

MAN-100411

SITRANS LVL200E - Operating Instructions

55328-EN-170712

Ʋ Sensor

1 g with 5 … 200 Hz according EN 60068-2-6 (vibration

at resonance) with sensor length up to 50 cm (19.69 in)
With a sensor length > 50 cm (19.69 in) you have to fix

the extension tube with a suitable support. See mounting

instructions.

Electromechanical data - version IP 66/IP 67 and IP 66/IP 68; 0.2 bar

Cable entry/plug

Ʋ Single chamber housing

– 1 x cable gland M20 x 1.5 (cable: ø 5 … 9 mm), 1 x

blind plug M20 x 1.5

or:

– 1 x closing cap ½ NPT, 1 x blind plug ½ NPT

or:

– 1␣x plug (depending on the version), 1␣x blind stopper

M20␣x␣1.5

Screw terminals

for wire cross-section up to 1.5 mm² (AWG 16)

Adjustment elements

Sensitivity switch

Ʋ ≥ 0.5 g/cm³

0.5 … 2.5 g/cm³ (0.018 … 0.09 lbs/in³)

Ʋ ≥ 0.7 g/cm³

0.7 … 2.5 g/cm³ (0.025 … 0.09 lbs/in³)

Voltage supply

Operating voltage (via the signal conditioning instrument)

Ʋ Non-Ex instrument

12 … 36 V DC

Ʋ Ex-d instrument (ATEX, FM, CSA)

12 … 36 V DC

Ʋ Ex-ia instrument (ATEX)

12 … 29 V DC

Ʋ Ex-ia instrument (FM, CSA)

12 … 31 V DC

Electrical protective measures

Protection rating

Ʋ Plastic housing

IP 66/IP 67 (NEMA Type 4X)

Ʋ Aluminium and stainless steel (stand-

ard)

IP 66/IP 68 (0.2 bar), NEMA Type 6P

Ʋ Aluminium and stainless housing

(optionally available)

IP 66/IP 68 (1 bar), NEMA Type 6P

Protection class

Functional safety (SIL)

Functional safety according to IEC 61508/IEC 61511

Ʋ Single channel architecture (1oo1D) up to SIL2

Ʋ Multiple channel architecture

see supplementary instructions manual "

Safety Manual

(SIL)

Depending on the version M12 x 1, according to ISO 4400, Harting, 7/8" FF.

A suitable cable is required for maintaining the protection rating.

Содержание SITRANS LVL200E













































Результаты поиска

Содержание SITRANS LVL200E

Отзывы:

Похожие инструкции для SITRANS LVL200E

Бренды по названию

Популярные бренды

Siemens SITRANS LVL200E, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS LVL200E

Отзывы:

Похожие инструкции для SITRANS LVL200E

Бренды по названию

Популярные бренды