Siemens SITRANS L LU240 Скачать руководство пользователя

Страница: 51 / 60

9.4

Outputs

Analog output

● 4 to 20 mA

● 800 ohms maximum

● ±0.02 mA accuracy
● Resolution of <1 μA

9.5

Construction

Process connections

● 2" NPT (ASME B1.20.1) (tapered thread)
● R 2" [(BSPT), EN 10226-1] (tapered thread)
● G 2" [(BSPP), EN ISO 228-1] (parallel thread)

Transducer/nosecone

● Buna-N seal
● PVDF (polyvinylidene fluoride)
● ETFE (ethylene-tetrafluoroethylene)

Enclosure

Body material

Plastic (PBT/PC - polybutylene terephtha‐

late/polycarbonate)

Electrical connections/cable en‐

tries

● 2 x M20 x 1.5 (one general purpose

cable gland and one blocking plug
provided)

● 1 x 1/2" NPT

Ingress protection

● IP66, TYPE 4X
● IP68, TYPE 6

Clear lid

Plastic (PBT/PC - polybutylene terephthalate/polycarbonate)

Blind lid

Plastic (PC - polycarbonate)

Weight

0.93 kg

Installation torques

Cable gland to enclosure

(Siemens supplied, metric)

10 Nm

Note
Specific configuration requirements
Check the ambient and operating temperatures under Operating conditions (Page 52) and

Process (Page 52); also check Approvals (Page 53) for the specific configuration you are about

to use or install.
Use approved cable gland/conduit seal to maintain Type 4X, Type 6, IP66, IP68 ratings.

For dimensions of parts listed above, see Dimension drawings chapter in full operating

instructions.

Technical data

9.5 Construction

SITRANS Probe LU240 with mA/HART

Compact Operating Instructions, 10/2018, A5E42673704-AB

Содержание SITRANS L LU240





























































Результаты поиска

Содержание SITRANS L LU240

Отзывы:

Похожие инструкции для SITRANS L LU240

Бренды по названию

Популярные бренды

Siemens SITRANS L LU240, Краткое руководство по эксплуатации

Результаты поиска

Содержание SITRANS L LU240

Отзывы:

Похожие инструкции для SITRANS L LU240

Бренды по названию

Популярные бренды