Siemens SITOP PSU8200 Скачать руководство пользователя страница 55

Страница: 55 / 66

SITOP PSU8200 1ph
Manual, 11.2014, C98130-A7633-A1-3-7629

Applications

9.1

Parallel connection to increase power rating

To increase the power rating, SITOP PSU8200 power supplies of the same type can be

directly connected in parallel.
The following must be observed:

●

The cables connected to each power supply at terminals "+" and "-" must have identical

lengths and the same cable cross-sections (or the same impedance) up to a common

external connection point (terminal strip) if possible.

●

The power supplies connected in parallel must be switched on simultaneously with a

common switch in the line feeder cable (e.g. with the main switch available in control

cabinets).

●

The output voltages measured in no-load operation for the power supplies that are not yet

connected in parallel should not deviate more than a maximum of 50 mV. This usually

corresponds to the factory setting. If the output voltage is changed, you should connect

the "-" terminals and then, in no-load operation, measure the voltage difference between

the "+" terminals that have not yet been connected. The voltage difference should not

exceed 50 mV.

●

Switch selector switch "A" (see Figure 2-8 Selector switch (Page 16)) to "Parallel

operation".

Figure 9-1

Parallel connection

Содержание SITOP PSU8200



































































Результаты поиска

Содержание SITOP PSU8200

Отзывы:

Похожие инструкции для SITOP PSU8200

Бренды по названию

Популярные бренды

Siemens SITOP PSU8200, Руководство пользователя

Результаты поиска

Содержание SITOP PSU8200

Отзывы:

Похожие инструкции для SITOP PSU8200

Бренды по названию

Популярные бренды