Siemens SITOP PSU8200 Скачать руководство пользователя страница 16

Страница: 16 / 66

Description, device design, dimension drawing

2.5 Change-over switch

SITOP PSU8200 1ph

Manual, 11.2014, C98130-A7633-A1-3-7629

2.5

Change-over switch

Figure 2-8

Selector switch

The two switches A and B are used to influence the output characteristic curve:

Switch

OFF

influences the output

characteristic in the

load range

Parallel operation:

'Soft' characteristic curve (see, e.g. Figure 6-6 Output

characteristic curve 6EP3333-8SB00-0AY0 parallel

operation (Page 42)) for the parallel operation of two

or more devices: The output voltage falls with increas-

ing output current (namely, also for the overcurrent

pulse!).

This means that for full output current the highest

output voltage can normally no longer be attained.

Single operation:

Delivery state

"Hard" characteristic curve (see, e.g.

Figure 6-3 Output characteristic curve

6EP3333-8SB00-0AY0 stand-alone op-

eration (Page 41)) for normal operation

(single operation): The output voltage is

independent of the output current.

influences the output

characteristic in the

overload range

Latching shutdown:

If the output current rises above the rated value and

above the current limit, the device reduces the output

voltage (see, e.g. Figure 6-9 Output characteristic

curve 6EP3333-8SB00-0AY0 latching shutdown

(Page 43)). If the output voltage falls below 20 V, the

device shuts down latching, the red LED lights up.

This limit voltage of 20 V is independent of the set

output voltage. The "Short-term overload current"

feature is not available in this operating mode.

6EP3333-8SB00-0AY0 and 6EP3334-8SB00-0AY0

are reset using power supply OFF for a minimum of

60 s or remote OFF and ON at the remote contact.

6EP1336-3BA10 is reset by switching the power sup-

ply OFF for at least 5 s.

To also guarantee that large capacitances can be

charged at the output in this operating mode, a non-

latching shutdown is not performed during the first

10 s after power ON or remote ON. During these first

10 s, the device responds for overload as if the switch

is OFF.

Constant current:

Delivery state

If the output current rises above the rated

value and above the current limit, the

device reduces the output voltage. The

yellow LED lights up if the output voltage

falls below 20 V.

Содержание SITOP PSU8200



































































Результаты поиска

Содержание SITOP PSU8200

Отзывы:

Похожие инструкции для SITOP PSU8200

Бренды по названию

Популярные бренды

Siemens SITOP PSU8200, Руководство пользователя

Результаты поиска

Содержание SITOP PSU8200

Отзывы:

Похожие инструкции для SITOP PSU8200

Бренды по названию

Популярные бренды