Siemens SITOP PSU8200 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 66

Siemens SITOP PSU8200 Скачать руководство пользователя страница 15

Description, device design, dimension drawing

2.4 Status displays and signaling

SITOP PSU8200 1ph
Manual, 11.2014, C98130-A7633-A1-3-7629

15

6EP1336-3BA10 (24 V/20 A)

Operating display

④

LED green, lit for "24 V O.K."
Yellow LED lit for overload condition (Ua <20 V ±0.5 V)
Red LED lit for latching shutdown as a result of overload

(only for selector switch B in the "ON" position)

Signaling contact

⑤

Relay contact (NO contact, contact rating 30 V AC/0.5 A, 30 V DC/1 A) for

"24 V O.K."

Figure 2-7

Operating display and signaling contact for 6EP1336-3BA10

Signaling

6EP1336-3BA10 (24 V/20 A)

LED green (4.1) off
Signaling contact (5), contacts 13-14 open

(quiescent position)

No supply voltage

Green LED (4.1) lit
Signaling contact (5), contacts 13-14 closed

Normal operation, output voltage >20 V ±0.5 V

Yellow LED (4.2) lit
Signaling contact (5), contacts 13-14 open

(quiescent position)

Overload (U

a

<20 V ±0.5 V)

Red LED (4.3) lit
Signaling contact (5), contacts 13-14 open

(quiescent position)

Latching shutdown due to overload

«
...
13
14
15
16
17
...
»

Содержание SITOP PSU8200



































































Отзывы:

Нет отзывов