Siemens SINUMERIK ONE NCU 1740 Скачать руководство пользователя страница 133

Страница: 133 / 164

Signal type

Meaning

Supply voltage

GND

Protective ground (reference potential)

Note

Digital and analog signals must not be laid together within a cable.

12.3.4.2

X1 power supply

Properties

This interface is intended exclusively for the connection of the external 24 V power supply.

On the module side, the power supplies are protected against:

• Polarity reversal

• Short-circuit (elec. current limitation of the outputs)

• Overload (self-restoring PTC fuse - Multifuse)

Requirements placed on the DC power supply

WARNING

Inadequately fused supply cables can be life-threatening

In the case of supply lines > 10 m, protectors must be installed at the device input in order to
protect against lightning (surge).

The DC power supply must be connected to the ground/shield of the I/O module for EMC and/
or functional reasons. For EMC reasons, this connection should only be made at one point; see
also EMC Installation Guide.

Table 12-34 Requirements of the DC power supply

Rated voltage

According to EN 61131-2

24 VDC

Voltage range (average value)

20.4 VDC to 28.8 VDC

Voltage range (dynamic)

18.5 to 30.2 VDC

Voltage ripple peak-to-peak

5% (unfiltered 6-pulse rectifi‐
cation)

Ramp-up time at POWER ON

Any

Non-periodic overvoltages

≤ 35 V

Duration of overvoltage

≤ 500 ms

Recovery time

≥ 50 s

Events per hour

≤ 10

Connectable components

12.3 PP 72/48D PN 2/2A PN

NCU 1740
Equipment Manual, 10/2021, A5E51087503B AA

133

Содержание SINUMERIK ONE NCU 1740





































































































































































Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды

Siemens SINUMERIK ONE NCU 1740, Руководство по эксплуатации оборудования

Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды