Siemens SINAMICS G120 PM240P-2 страница 41 Скачать руководство пользователя

Страница: 41 / 106

Connecting

4.1 Permissible line supplies

Power Module PM240P-2
Hardware Installation Manual, 06/2020, A5E37800827C AD

4.1.4

Requirements for the protective conductor

Overview

A high leakage current flows through the protective conductor in converter operation. The

protective conductor of the converter must not be interrupted for safe touch protection in

converter operation.
This primarily results in requirements for the minimum conductor cross-section of the

protective conductor.
No restriction applies to the length of the protective conductor for touch protection. However,

short protective conductors are advantageous for EMC-compliant installation.

Description

WARNING

Electric shock due to interrupted protective conductor
The drive components conduct a high leakage current via the protective conductor.

Touching conductive parts when the protective conductor is interrupted can result in death

or serious injury.

•

Comply with the requirements for the protective conductor.

①

Protective conductor for line feeder cables

②

Protective conductor for converter line feeder cables

③

Protective conductor between PE and the control cabinet

④

Protective conductor for motor feeder cables

Содержание SINAMICS G120 PM240P-2











































































































Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды

Siemens SINAMICS G120 PM240P-2, Руководство по установке

Результаты поиска

Содержание SINAMICS G120 PM240P-2

Отзывы:

Похожие инструкции для SINAMICS G120 PM240P-2

Бренды по названию

Популярные бренды