Siemens SIMOTION TM15 Скачать руководство пользователя страница 81

Страница: 81 / 99

Technical data

6.2 System behavior

TM15 / TM17 High Feature Operating Manual
Commissioning Manual, 05/2009

6.2.4

System behavior with outputs of output cam

The system behavior for outputs of output cam is shown in the figure below:

,32WDVN

6HUYR

2XWSXWRI
RXWSXW
FDP

6HUYR

2))

RXW

,32

RXW

2))

Figure 6-8

System behavior with outputs of output cams (call TO Output Cam and user program in

the IPO cycle clock)

In order to switch an output of an output cam in the shaded area of IPO #3, the Output Cam

technology object (TO) determines the switching positions in IPO #1. These switching

positions are converted in the following position control clock cycle to time stamp T

and T

off

and then transferred at the beginning of IPO #3.
The same system timing applies to the Output Cam Track technology object.

6.2.5

Interpolation

A linear interpolation is used to calculate the output cam switching points and for the

conversion of measuring input edges to axis positions. This can affect the accuracy in the

event of strong axis acceleration.
The time that elapses between the "state change on the terminal" and the "calculation in the

technology object" can be obtained from the timing diagrams.

Содержание SIMOTION TM15




































































































Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMOTION TM15, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание SIMOTION TM15

Отзывы:

Бренды по названию

Популярные бренды